Nittan CKLD-KPT2 Instruction Manual Download | Manualshive

Page: 16 / 18

background image

16

The remote test function is supported by using Remote Station for
Beam Detector (LP04/ LP05) to connect the Detector to P-type
control panel. Test is remotely performed by operating the test
switch of the Remote Station. Refer to the Operation Instruction
Manual of the Remote Station for test method.

Test Function

«
...
14
15
16
17
18
»

Summary of Contents for CKLD-KPT2



















Reviews:

No comments

Related manuals for CKLD-KPT2

Brand: ThermoWorks Pages: 2

Brand: JBM Pages: 24

Brand: SOUNDMASTER Pages: 74

Brand: Smartwares Pages: 2

Vinson 200 11422

Brand: Landmann Pages: 44

Brand: Sanful Pages: 12

Brand: Gastronoma Pages: 29

Brand: WOOX Pages: 47

Brand: Trevi Pages: 8

Brand: Prestige Pages: 8

Brand: JBL Pages: 12

Brand: Toyota Pages: 12

Brand: Fire-Lite Alarms Pages: 48

Great Outdoors Smoky Mountain 3425BGW

Brand: Landmann Pages: 29

Home 4 You ZHS20

Brand: Schwaiger Pages: 2

Brand: Satel Pages: 8

Brand: La Crosse Technology Pages: 18

Brand: La Crosse Technology Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands