10
ninjakitchen.com
11
ninjakitchen.com
CARE & MAINTENANCE
CLEANING
• Hand-Washing
Separate all parts and wash in warm,
soapy water with a soft cloth. Thoroughly
rinse and air-dry all parts.
• Dishwasher
All parts, except the motor base, are
dishwasher safe.
• Motor Base
Unplug the motor base before cleaning.
Wipe with a clean, damp cloth.
DO NOT
use abrasive cloths, pads, or
brushes to clean the base.
• Using the Cleaning Brush
Use the included cleaning brush to clean
hard-to-reach places, as well as remove
excess residue.
Use the end of the cleaning brush to clear
any buildup left over after juicing.
Use the bristle side of the cleaning
brush to clean the filter, if needed.
STORING
For cord storage, wrap cord with hook-and-
loop fastener near the back of the motor base.
DO NOT
wrap the cord around the bottom
of the base for storage.
When moving the unit, lift from the bottom
of the motor base. Store the auger and filter
assembled in the feed chute chamber with
the pulp spout installed. Place the juice jug
into the pulp container for easy storage.
OVERLOADING THE UNIT
This unit features a unique safety system
that prevents damage to the motor and
drive system should you inadvertently
overload the motor. If the unit is overloaded,
the motor will be temporarily disabled.
Should this occur, wait 2 minutes, then press
START/STOP to start the unit.
If your unit needs servicing, please call
Customer Service at 1-877-646-5288. So we
may better assist you, please register your
product online at
registeryourninja.com
and
have the product on hand when you call.
ORDERING REPLACEMENT PARTS
To order additional parts and attachments,
visit
ninjaaccessories.com
.
IMPORTANT:
DO NOT
add water to the
feed chute while the unit is operating to
clean the unit.
TROUBLESHOOTING GUIDE
WARNING: To reduce the risk of shock and unintended operation,
unplug unit before troubleshooting�
The REVERSE program is not operating�
•
After pressing and holding REVERSE, there will be a beep and a brief pause, then the
auger will rotate in the opposite direction. Release REVERSE to stop. Repeat as needed.
Press START/STOP to resume normal operation.
There is a buildup of pulp in the feed chute chamber�
•
There may be a clog in the pulp spout. Press START/STOP to stop the unit, then
remove the pulp spout. Use the end of the cleaning brush to clear the clog, then
reinstall the pulp spout to the feed chute chamber. Resume juicing.
•
For best results, allow juicer to process each ingredient before adding more to the feed
chute. Use the tamper to push ingredients down through the feed chute, as needed.
The unit stopped working and is beeping�
•
The unit was overloaded with ingredients. Wait 2 minutes then press START/STOP
to start the unit.
Can I juice fruit with seeds and pits in it?
•
No. Seeds and pits should be removed from the fruit prior to juicing. For example,
remove the seeds from cherries and the pit from a plum.
Can I juice frozen fruits and vegetables or add ice?
•
No, do not use frozen fruit, frozen vegetables, or ice with this unit.
The unit makes a squeaking noise when I juice certain ingredients�
•
When the auger is breaking down fibrous ingredients like apples, celery, herbs and leafy
greens, the unit will sometimes make this noise. This is normal and not a cause for concern.
There is clogging in the pulp filter�
•
When juicing solely fibrous ingredients, such as pineapple, you may have to clear the filter
of pulp more often, especially when using the no pulp filter.
The unit is producing less juice than I anticipated based on the amount of produce I used�
•
With the Ninja Cold Press Juicer, you can expect 1 lb. of produce to yield approximately
8 oz. of juice.*
•
Depending on the seasonality of ingredients, you may experience lower juice and pulp
yield when using the No Pulp Filter. If this occurs, try using the Some Pulp Filter.
ENGLISH
