background image

4

TRUCK BOOSTER

Original Instructions

1  Safety Precautions and Warnings

Symbols used to mark 
 instructions

Before starting up 
your high-pressure 
washer for the fi rst 
time, this instruc-
tion manual must 

be read through carefully. Save 
the instructions for later use.

Safety instruc-
tions marked with 
this symbol must 
be observed to 

prevent danger to persons.

This symbol is 
used to mark 
safety instruc-
tions that must 
be observed to 
prevent damage 

to the machine and its perfor-
mance.

This symbol 
indicates tips 
and instructions 
to simplify work 

and to ensure a safe operation.

For your own safety

The high-pressure washer 
may only be used by persons 
instructed in its use and who 
have been expressly authorised 
to do so.

Although extremely easy to 
operate, children should not be 
allowed to use the washer.

Warning

Inhalation of aerosols can be 
hazardous to health.
Where applicable use a device 
in order to avoid or reduce 
aerosols production, e.g., a 
shield covering the nozzle.
For protection against aerosols 
use a respiratory mark of class 
FFP 2 or higher.

General

When using the high-pressure 
hot water washer all existing 
national regulations must be 
observed. Beyond the instruc-
tion manual and the current 
national legal regulations for 
prevention of accidents, also 
the approved rules for safe 
working must be observed.

Any method of use endangering 
the safety of persons or equip-
ment is forbidden.

Before use

Before starting up your high-
pressure hot water washer 
check that it is in a regular 
condition. Electric plugs and 
couplings must be watertight.

Check the electric cables at 
regular intervals for damage 
and wear. Only use the high-
pressure hot water washer if 
the electric cable is all right 
 (damaged electric cables can 
cause electric shock!)

Important instructions

Connection to public drinking 
water supply must be per-
formed in accordance with the 
applicable regulations in your 
country.

IMPORTANT:

 Only use water 

without impurities! 

Before each use of your high-
pressure hot water washer 
check the most important visual 
parts.

High-pressure 
jets can be 
dangerous if 
misused. Never 
direct the wa-
ter jet towards 
people, pets, 
electric wiring, or 
the machine itself.

Spray handle and lance are af-
fected by a thrust during   op-
eration - therefore always hold 
the spray lance fi rmly with both 
hands.

Never try to clean clothes or 
footwear on yourself or other 
persons.

Operator and anyone in imme-
diate vicinity of the site of clean-
ing should take action to protect 
himself from being struck by 
debris dislodged during opera-
tion.

Check that cleaning will not 
result in dangerous substances 
(e.g. asbestos, oil) being 
washed off the object to be 
cleaned and harming the envi-

Nilfisk-AL

T

O

   No. 301003191

Summary of Contents for TRUCK BOOSTER
































Reviews: