background image

26

SH SOLAR E, D

Original Instructions

7 Trouble 

Shooting

You have chosen the best quality and therefore deserve the best service. All machines feature an “Er-
ror detection system” that will stop the machine in case of a severe error that needs immediate atten-
tion. The red light of the STOP button will fl ash, and the display in the inspection window will indicate 
the nature of the error.  Please refer to the specifi c section (7.2 to 7.3) that represents your machine.

Though the user can correct some of these errors, you should note the error and contact the nearest 
Nilfi sk service organisation. To avoid unnecessary dis ap point ments, you should check section "

7.1 

General trouble shooting

" before contacting the nearest Nilfi sk service organisation.

Should other malfunctions occur than those mentioned in sections 7.1 to 7.3, please contact your 
nearest Nilfi sk service organisation.

7.1  General trouble shooting - all models

 Symptom 

Reason 

Action

Machine will not start

 

>  A fuse has blown 

•  Change the fuse.

(NO ERROR indication)
 

>  Power disconnected 

•  Connect power.

Fuses blow

 

>  Installation does not  

•  Change to an installation. 

 

 

correspond to the ampere 

 

corresponding to the ampere  

 

  consumption of the machine 

  consumption of the machine  

 

  

 at 

minimum. 

 

  

 Change 

the 

fuse.

Working pressure too low 

>  Nozzle worn 

•  Replace the nozzle.

 

>  Wrong spray lance 

•  Replace the spray lance 

 

  

 (see 

section 

4.1.4).

 

>  Reduction valve of spray  

•  Turn reduction valve com-  

 

  lance not adjusted to max. 

  pletely counter-clockwise

 

 pressure. 

 (see 

section 

4.1.4).

 

>  Nozzle partly clogged up 

•  Clean the nozzle 

 

 

  

 (see 

section 

6.4).

Working pressure fl uctuating

 

>  Insuffi cient water supply 

•  Dismount the cabinet and  

 

   

  check that the water tank is  

 

   

  not drained of water during  

 

 

 

 

operation of the machine. If it  

 

   

  is, clean the water inlet fi lter  

 

   

  of the machine. If that does  

 

   

  not solve the problem, the  

 

   

  water supply for the machine  

 

  

 is 

insuffi 

cient.   

 

 

   

 NB! 

Avoid long, thin hoses  

 

  

 (min. 

3/4").

 

>  High pressure hoses too long 

•  Dismount high pressure   

 

    

  extension hoses and retry. 

 

   

  Extension hose max. 50 m.

 

   

 

NB!

 Avoid long extension  

Summary of Contents for SH SOLAR D





































Reviews: