Nilfisk-Advance MC 2C Series Instruction Manual Download Page 15

15

Original Instructions

  

6 Fields of application and working 

methods

6.1 General

Efficient high pressure cleaning is achieved by following a few 

guidelines, combined with your own personal experience of spe

-

cific cleaning tasks. Accessories and detergents, when correctly 

chosen, can increase the efficiency of your pressure washer. Here 

is some basic information about cleaning.

6.1.1 Detergent and foam

Foam or detergent should be applied onto dry surfaces so that the 

chemical product is in direct contact with the dirt. Detergents are 

applied from bottom to top, for example on a car bodywork, in order 

to avoid “super clean” areas, where the detergent collects in higher 

concentration and streams downwards. Let the detergent work for 

several minutes before rinsing but never let it dry on the surface 

being cleaned. 

Note: 

It is important that the detergents do not dry 

up. Otherwise the surfac that has to be cleaned can be da maged.

6.1.2 Mechanical effect

 

In order to break down tough layers of dirt, additional mechanical 

effect may be required. Special wash brushes offer this supple

-

mentary effect that removes stubborn dirt, traffic film or the like.

Summary of Contents for MC 2C Series
























Reviews: