background image

67

English 07/16

Service Manual

HR15/17N HYBRID DC

32

EM Brake Open/Short

ShutdownEMBrake;
ShutdownThrottle;
FullBrake.

1. Open or short on driver load.
2. Dirty connector pins.
3. Bad crimps or faulty wiring.

Set: 

Electromagnetic brake driver 

(pin 5) is either open or shorted. 
This fault can be set only when 
EM Brake Type > 0.

Clear: 

Correct open or short, 

and cycle driver.

33

Coil3 Driver Open/Short

ShutdownDriver3.

1. Open or short on driver load.
2. Dirty connector pins.
3. Bad crimps or faulty wiring.

Set: 

Driver 3 (pin 4) is either open 

or shorted.

Clear: 

Correct open or short, 

and cycle driver.

34

Coil4 Driver Open/Short

ShutdownDriver4.

1. Open or short on driver load.
2. Dirty connector pins.
3. Bad crimps or faulty wiring.

Set: 

Driver 4 (pin 3) is either open 

or shorted.

Clear: 

Correct open or short, 

and cycle driver.

35

PD Open/Short

ShutdownPD.

1. Open or short on driver load.
2. Dirty connector pins.
3. Bad crimps or faulty wiring.

Set:

 Proportional driver (pin 2) is 

either open or shorted.

Clear: 

Correct open or short, 

and cycle driver.

36

Encoder Fault

ShutdownEMBrake;
ShutdownThrottle.

1. Motor encoder failure.
2. Bad crimps or faulty wiring.
3. See Monitor menu» Motor: 
Motor RPM.

Set:

 

Motor encoder phase failure 

detected.

Clear: 

Cycle KSI.

37

Motor Open

ShutdownMotor;
ShutdownMainContactor;
ShutdownEMBrake;
ShutdownThrottle;
FullBrake;
ShutdownPump.

1. Motor phase is open.
2. Bad crimps or faulty wiring.

Set:

 Motor phase U, V or W detected 

open.

Clear: 

Cycle KSI.

38

Main Contactor Welded

ShutdownMotor;
ShutdownMainContactor;
ShutdownEMBrake;
ShutdownThrottle;
FullBrake;
ShutdownPump.

1. Main contactor tips are 
welded closed.
2. Motor phase U is 
disconnected or open.
3. An alternate voltage path 
(such as an external precharge 
resistor) is providing a current 
to the capacitor bank (B+ 
connection terminal).

Set: 

Just prior to the main contactor 

closing, the capacitor bank voltage 
(B+ connection terminal) was 
loaded for a short time and the 
voltage did not discharge.

Clear: 

Cycle KSI.

Code Programmer LCD Display 

Effect of fault

Possible Cause

Set/Clear Conditions

Summary of Contents for HYBRID DC HR15N Series
















































































Reviews: