Nice X-Bar, Instructions And Warnings For Installation And Use

Page: 22 / 22

EN
8 – English
IMPORTANT – In the programming procedure, the maximum time interval
that can elapse between activation of one key and the next is 10 seconds.
When this time elapses, the procedure terminates automatically, memorising
the modifications made up until then.
6.2 - Level two programming (adjustable parameters)
All level 2 parameters are set by default as highlighted in grey in Table 7 , and
may be modified at any time as explained in
Table 8
.
The parameters can be set on a scale from 1 to 8 . To check the value corre-
sponding to each LED see
Table 7
.
TABLE 6 - First level functions
LED Description Example
L1 Automatic closure
This function performs automatic closure of the pole after the programmed pause time. Factory setting:
30 seconds . Value programmable from 5 to 200 seconds .
L2 Reclose after photo This function enables the pole to remain in Opening position for the time required for transit . When the function is
active, operation depends on the parameter set in the function “Automatic closure”:
• with “Automatic closure” active, the Opening manoeuvre stops immediately after the photocells are
disengaged and the Closure manoeuvre starts after 5 seconds .
• with “Automatic closure” not active, the pole always reaches the maximum Opening position (even if the
photocells are disengaged beforehand) and Closure starts after 5 seconds .
L3 Always close This function is useful in the event of a power failure, even brief . In fact if this function is active(ON), when power
is restored, the control unit detects the pole as open and starts Closure . For reasons of safety the Closure
manoeuvre is preceded by a 3-second pre-flashing interval.
L4 Stand by The Stand-by function allows consumptions to be reduced . If active, 1 minute after the end of the manoeuvre, the
control unit turns off the “Bluebus” output (connected devices) and all the LEDs apart from the Bluebus LED which
will flash more slowly. When the control unit receives a command normal operation is restored. When using X-Bar
with the Solemyo system, a longer Stand By mode must be set . This operation is performed using the Oview
programmer .
L5 Deceleration long This function enables the user to double the space for starting deceleration, both in Opening and Closing . If the
function is deactivated, deceleration is short .
L6 Pre-flash
This function activates a pause of 3 seconds between activation of the flashing light and the start of a manoeuvre.
L7 Sensitivity
When this function is set to “ON” the level of control unit sensitivity in obstacle detection can be increased
considerably . If used as a means to read the “impact force” of the motor, the values “speed” and “motor force”
must be set accordingly in the level 2 menu .
L8 Direction of motor rotation
This parameter enables inversion of the direction of motor rotation to enable barrier installation on the right; the
factory setting is “OFF” (standard motor rotation – pole closure on left) .
Important
– If the function is activated, the Opening and Closing positions must be memorised again (Paragraph 4 .5) .
TABLE 7 - Second level functions
Input LED Parameter LED (level) Value Description
L2 L1
L2
L3
L4
L5
L6
L7
L8 Open – stop – close - stop
Open – stop – close - open
Open – close – open - close
Apartment block (more than 2 sec . generates Stop)
Apartment block 2 (less than 2 sec . generates partial opening) .
Step by step 2
Hold-to-run
Opening in semi-automatic mode, closing in dead man mode Sets the sequence of commands as-
sociated with the input or the radio
control: “Step by step”.
Function
Step by
step
L1 L1
L2
L3
L4
L5
L6
L7
L8 5 seconds
10 seconds
20 seconds
40 seconds
60 seconds
80 seconds
120 seconds
200 seconds Sets the pause time, i .e . the time that
passes between the end of an ope-
ning manoeuvre and the start of an
automatic closing manoeuvre
This parameter is only effective if the
“automatic Closure” is active .
Time
Pause
L3 L1
L2
L3
L4
L5
L6
L7
L8 Speed 1 (30% - slow)
Speed 2 (47%)
Speed 3 (65%)
Speed 4 (82%)
Speed 5 (100%) - fast
Open V3, Close V2
Open V4, Close V3
Open V5, Close V4 Sets the motor speed during normal
travel .
Speed
Motor
L4 L1
L2
L3
L4
L5
L6
L7
L8 Pole Open Indicator Function (24 V - 10 W)
Active if pole closed (24 V - 10 W)
Active if pole open(24 V - 10 W)
Flashing light(12 V - 21 W)
Flashing light for pole lights (24 V - 10 W)
Electric lock(24 V - 10 W)
Suction cup(24 V - 10 W)
Maintenance indicator (24 V - 10 W) Selects the type of device connected
to the FLASH output .
Important! – If the programmed set-
ting is modified, check the type of vol-
tage of the new device connected to
the FLASH terminal and ensure that it
corresponds to the type of voltage of
the selected programming level .
Output
FLASH