background image

8

Installing the cabinet.

06

02

Establish where the traffic barrier cabinet 
mounting position needs to be. 

If an concrete plinth already exists, skip to step 
06. 

If no concrete plinth is in place, continue on to 
step 02.

Begin by digging a hole for the foundation plinth 
to be cast in. In places where water can possibly 
dam up and collect around the base, you will 
want to use shutter boarding to generate a 
raised plinth. 

Once the hole has been dug, prepare your 
cabling conduits. Ref: Cable requirements on 
previous page.

Fasten the 4 J-bolt anchors onto the base plate 
with one nut above and one nut below the base 
plate. 

NB!

 the nut below the base plate must be 

threaded all the way down to the end of the 
thread on each bolt. 

After pouring the concrete into the prepared 
hole, press the base plate down onto the 
concrete and ensure the base plate is 
horizontally level on top of the concrete. 

01.

02.

03.

04.

Allow sufficient time for the concrete to set and 
cure before working with the mounting plinth 
further. Typically this takes about 2 weeks. 

After the concrete has set and cured sufficiently, 
remove the 4 upper nuts from the now secured 
bolts. 

05.

Summary of Contents for WIDE L



























Reviews: