background image

– English

IMPORTANT SAFETY INSTRUCTIONS

 
WARNING

To reduce the risk of severe injury or death:

• READ AND FOLLOW ALL INSTRUCTIONS.

Never let children operate or play with door controls. Keep the remote control away from children.

• Always keep the moving door in sight and away from people and objects until it is completely closed. NO ONE SHOULD CROSS 

THE PATH OF THE MOVING DOOR.

• For vertically moving doors: NEVER GO UNDER A STOPPED, PARTIALLY OPEN DOOR.
• For horizontally moving doors: NEVER GO THROUGH A STOPPED, PARTIALLY OPEN DOOR.

Test door opener monthly. The garage door MUST reverse on contact with a 38-mm (1-1/2-inch) high object (or a 2 by 4 board 

laid flat) on the floor. After adjusting either the force or thelimit of travel, retest the door opener. Failure to adjust the opener 

properly increases the risk ofsevere injury or death.

• For vertically moving doors for products having an emergency release, when possible, use the emergency release only when 

the door is closed. Use caution when using this release with the door open. Weak or broken springs are capable of increasing 

the rate of door closure and increasing the risk of severe injury or death.

• KEEP GARAGE DOORS PROPERLY BALANCED. See user’s manual. An improperly balanced door increases the risk of severe 

injury or death.
- For vertically moving doors: have a qualified service person make repairs to cables, spring assemblies, and other hardware.
- For horizontally moving doors: have a qualified service person make repairs and hardware adjustments before installing the 

opener.

• Where possible, install the door operator 2.14 m (7 ft) or more above the floor. For products having an emergency release, 

mount the emergency release within reach, but at least 1.83 m (6 ft) above the floor and avoiding contact with vehicles to avoid 

accidental release.

• For operator systems equipped with an unattended operation feature, the following statement shall be included: “This operator 

system is equipped with an unattended operation feature. The door could move unexpectedly. NO ONE SHOULD CROSS THE 

PATH OF THE MOVING DOOR.”

• SAVE THESE INSTRUCTIONS.

Be careful when activating the manual unlocking device (manual manoeuvre), as an open door may fall suddenly due to weak or broken 
springs, or if it is unbalanced.

If the power cable is damaged, it must be replaced by the manufacturer or by an appointed servicing company or similarly qualified person 
in order to prevent any form of risk.

Summary of Contents for SPY800KCE/V1

































Reviews: