Nice Neomat T Series Instructions And Warnings For Installation And Use Download Page 9

Page: 9 / 96

English –

Note

: if the programming described in point 4 is not confirmed the modifications are abort-

ed and the previous programming is maintained.

If after having programmed this function you wish to eliminate it, the procedure in table A13
must be followed, omitting step 3 which would modify position “1”.
When position “2” is programmed, the electronic control unit automatically calculates the
difference between positions “2” and “1”, so that each time a lower command is given, the
awning lowers to the greater of the two positions and then retrieves the fabric until arriving
to the lesser of the two positions.

4.3.8 - Programming of the “FTC” function

After having programmed positions “0” and “1”, position “S” can be programmed that acti-
vates the “FTC” function for the automation of awnings with an automatic hooking mecha-
nism. Until the mechanism is working correctly, position “1” must be programmed a few
centimetres after the hooking point so that hooking occurs when retracting from point “1”,
and position “S” is programmed a few centimetres after the release point so that the
ascent from point “S” is performed freely.
Follow the procedure indicated in table “12” to program position “S”:

––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Table “A12” - Programming the release position “S”
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––

01.

Press and hold down button

■

of a previously memorized

transmitter until you hear a beep (after about 5 seconds).

02.

Press and hold buttons

■ ▼

for another 5 seconds until

2 rapid beeps are heard. At this point the awning auto-
matically moves to position “1”.

03.

Use buttons

▼

and

▲

within 5 seconds to position the

awning in the release position “S” (below position “1”).

04.

Confirm the position by pressing buttons

▼

and

▲

of the

transmitter together within 5 seconds until 3 beeps are
heard. At this point the awning will automatically move to
position “0”.

Note

: if the programming described in point 4 is not confirmed the modifications are abort-

ed and the previous programming is maintained. If after having programmed this function
you wish to eliminate it, the procedure in table A13 must be followed, omitting step 3 which
would modify position “1”.

4.3.9 - Modifying position “1”

Follow the procedure indicated in table “A13” to modify position “1”:

––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Table “A13” - Modifying position “1”
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––

01.

Press and hold down button

■

of a previously memorized

transmitter until you hear a beep (after about 5 seconds).

02.

Press and hold buttons

■ ▼

for another 5 seconds until

2 rapid beeps are heard. At this point the awning auto-
matically moves to the position “1”.

03.

Use buttons

▼

and

▲

within 5 seconds to reposition the

awning in the new position to be programmed.

04.

Confirm the position by pressing buttons

■ ▼

of the

transmitter together within 5 seconds until 3 beeps are
heard and a short up and down movement is performed.

Note

: if the programming described in point 4 is not confirmed the modifications are abort-

ed and the previous programming is maintained.
By modifying position “1” the "FRT" and "FTC" functions are cancelled.

4.4 - Memory deletion

If you need to delete all the transmitter and the programmed operations, carry out the pro-
cedure shown in table A14.

The memory can be deleted:

• with a

non-memorized

transmitter starting from point A.

• with a

previously memorized

transmitter starting from point No. 1.

The following can be deleted:

•

only the memorized

transmitters, finishing at point No. 4

•

all data

(transmitters, sensor level, TTBUS address, etc.), completing the procedure

until point 6.

––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Table “A14” - Memory deletion
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––

Switch the motor off, activate the Step-by-Step input (by
connecting the White cable with the White/Black one)
and keep it active until the end of the procedure.

Power the motor and wait for the initial beeps.

01.

Press and hold down button

■

on a transmitter (about 5

seconds) until you hear a beep; then release it.

...