NI PXIe-4304 Calibration Procedure Download Page 1 | Manualshive

Page: 1 / 10

background image

CALIBRATION PROCEDURE

NI PXIe-4304/4305

32 Ch, 24-bit, ±42 V, 5 kS/s or 51.2 kS/s Simultaneous Filtered Data
Acquisition Module

This document contains the verification and adjustment procedure for the National Instruments
PXIe-4304/4305 module.

Contents

Software.................................................................................................................................... 1
Documentation.......................................................................................................................... 2
PXIe-4304/4305 Verification and Adjustment......................................................................... 3

Test Equipment................................................................................................................. 3

Connecting the TB-4304 .......................................................................................... 4

Test Conditions................................................................................................................. 5
Initial Setup....................................................................................................................... 6
Accuracy Verification....................................................................................................... 6
Adjustment........................................................................................................................ 8
EEPROM Update ............................................................................................................. 9
Reverification ................................................................................................................... 10

Specifications............................................................................................................................ 10
World Wide Support and Services ........................................................................................... 10

Software

Calibrating the NI PXIe-4304/4305 requires the installation of NI-DAQmx on the calibration
system. Driver support for calibrating the PXIe-4304/4305 was first available in
NI-DAQmx 15.1.1. For the list of devices supported by a specific release, refer to the

NI-DAQmx Readme

, available on the version-specific download page or installation media.

You can download NI-DAQmx from

ni.com/downloads

. NI-DAQmx supports LabVIEW,

LabWindows™/CVI™, C/C++, C#, and Visual Basic .NET. When you install NI-DAQmx, you
only need to install support for the application software that you intend to use.

ni.com/manuals

Deutsch

Français

1
2
3
...
»

Summary of Contents for PXIe-4304











Reviews:

No comments

Related manuals for PXIe-4304

Brand: UNITED Pages: 8

Brand: Dantherm Pages: 96

Brand: VAT Pages: 26

Brand: Gate Motors Pages: 6

Brand: Rabbit Pages: 38

Brand: U-Prox Pages: 3

Brand: D&R ELECTRONICS Pages: 12

Q Module WFZ16.Ox

Brand: QUNDIS Pages: 24

Brand: Rain Bird Pages: 11

LOOPDRIVE FIM-RC

Brand: 4EVAC Pages: 2

RSF-B mini Series

Brand: Harmonic Drive Pages: 32

Brand: Pilz Pages: 32

FLECK 5810 XTR2

Brand: Pentair Pages: 36

Tunnel Master Jr

Brand: ICS Pages: 70

Brand: Colorbeam Pages: 12

Brand: Kramer Pages: 60

Brand: Levven Pages: 2

Dynamic Boiler Controller

Brand: Intiel Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands