manualshive.com logo in svg

Nexo GEO M10, Setup Manual

Share
Download
Nexo GEO M10 Setup Manual Download Page 6

Page 6/79 

 

CONTENTS 

 

 

 

 

 

 

6.4 

F

LOWN CLUSTERS SETUPS

 ............................................................................................................................................... 41 

6.4.1  Described configurations .............................................................................................................................................. 41 
6.4.2  GEO M10 only flown with Lightweight Bumper ................................................................................................. 42 

6.4.3  GEO M10 flown with Touring Bumper .................................................................................................................... 46 
6.4.4  MSUB15 flown with Touring Bumper ..................................................................................................................... 50 

6.4.5  MSUB15 and GEO M10 flown with Touring Bumper ....................................................................................... 53 

6.5 

T

ESTING AND 

M

AINTENANCE OF THE SYSTEM

 ............................................................................................................. 58 

7 

SYSTEM CHECK ALIGNMENT GUIDELINES ................................................................................................... 59 

7.1 

GEO

 

M10

 

V

ERTICAL 

C

LUSTER DESIGN

......................................................................................................................... 59 

7.2 

S

TACKED 

MSUB15

 AND 

F

LOWN 

GEO

 

M10 ............................................................................................................... 59 

7.3 

D

RIVING THE 

MSUB15

S FROM THE 

AUX

 SEND

 .......................................................................................................... 60 

7.4 

R

ECOMMENDED INSTALLATION TOOLS AND EQUIPMENT

 .......................................................................................... 60 

7.5 

GEO

 

M10

 

–

 

MSUB15

 

S

YSTEM 

C

HECK 

L

IST

 ............................................................................................................... 61 

8 

TECHNICAL SPECIFICATIONS ............................................................................................................................ 62 

8.1 

MSUB15

 

S

UBWOOFER

 .................................................................................................................................................... 62 

8.1.1  System specifications ...................................................................................................................................................... 62 

8.1.2  Dimensions (mm/inches) .............................................................................................................................................. 62 

8.2 

GEO

 

M1012

 

&

 

GEO

 

M1025 ........................................................................................................................................ 63 

8.2.1  System specifications ...................................................................................................................................................... 63 
8.2.2  Dimensions (mm/inches) .............................................................................................................................................. 63 

8.3

 

GEO

 

M10

 ACCESSORIES

 .................................................................................................................................................. 64 

8.3.1  VNT-BUMPM10 .................................................................................................................................................................. 64 

8.3.2  VNT-EXBARM10 ................................................................................................................................................................ 65 
8.3.3  VNT-GSTKM10L ................................................................................................................................................................. 66 

8.3.4  VNT-GSTKM10S ................................................................................................................................................................. 67 

8.3.5  VNT-MNSTKM10 ............................................................................................................................................................... 68 
8.3.6  GMT-LBUMPM10 .............................................................................................................................................................. 69 

8.3.7  GMT-EXBARM10L ............................................................................................................................................................. 70 
8.3.8  GMT-FLGM10 ...................................................................................................................................................................... 71 

8.3.9  MST-WBMSUB15 .............................................................................................................................................................. 72 
8.3.10 

MST-COVMSUB15........................................................................................................................................................ 73 

8.3.11 

MST-2CASEMSUB15 ................................................................................................................................................... 74 

8.3.12 

GMT-3CASEM10 ........................................................................................................................................................... 75 

8.3.13 

GMT-6CASEM10 ........................................................................................................................................................... 76 

9 

GEO M10 & MSUB15 MODULES & ACCESSORIES LIST .............................................................................. 77 

10  USER NOTES ............................................................................................................................................................ 79 

 

Summary of Contents for GEO M10
















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands