Nexo GEO M10 Setup Manual Download Page 50

Page: 50 / 79

Page 50/79

GEO

M10

HARDWARE SETUP PROCEDURE

6.4.4 MSUB15 flown with Touring Bumper

Required items

1 or 2 hoists (not provided).

1 x VNT-BUMPM10

1 x VNT-EXBARM10 to fly on a single rigging point

IMPORTANT

When flying MSUB15 cluster, VNT-BUMPM10 must be set at 0°

If cluster is flown from 2 points, bumper must be maintained horizontal in its definitive
position as well as when lifting or lowering the cluster

If cluster is flown from a single point, extension bar must be used and hoist connected
to

“G” position

IMPORTANT

Maximum MSUB15 quantity for flown vertical cluster with VNT-BUMPM10 is 8.

Please check NS1 for mechanical Safety Working Load and acoustic computations.

IMPORTANT

Motor hoist must be rated to support entire cluster weight. Please check configuration

in NS1 for proper motor hoist rating

Summary of Contents for GEO M10
















































































Search results

Summary of Contents for GEO M10

Reviews:

Related manuals for GEO M10

Brands by name

Popular brands

Nexo GEO M10, Setup Manual

Search results

Summary of Contents for GEO M10

Reviews:

Related manuals for GEO M10

Brands by name

Popular brands