Nexo GEO M10 Setup Manual Download Page 43

Page: 43 / 79

GEO

M10

HARDWARE SETUP PROCEDURE

Page 43/79

IMPORTANT

Maximum GEO M10 quantity for flown vertical cluster with GMT-LBUMPM10 is 12 (and
eventually less).

Please check NS1 for mechanical Safety Working Load and acoustic computations.

IMPORTANT

Motor hoist must be rated to support entire cluster weight. Please check configuration

in NS1 for proper motor hoist rating

Procedure

GMT-LBUMP10 can be flipped front and back depending if its connects to GEO M10 Right or Left.

When connecting GEO M10

Left, bumper front is on the “A” hole index side

When connection GEO M10 Right, bumper front is on the “G” hole index side

GEO M10 Left

Position first GEO M10 so that Autorig

is at the bottom

Position bumper

(“A” hole at front) on top of first GEO M10

Remove the two BL820 quick release pins from their side storage position, and the BL825 quick
release pin of rear bumper link bar.

Connect bumper front points to GEO M10 with the BL820 quick release pins

Connect the bumper link bar (0° position) to GEO M10 rear rigging plate (hole marked “bumper”) Lock
with the quick release pin BL0825.

GEO M10 Right

Position GEO M10 so that Autorig

is at the top and set in automatic lock position

Position bumper

(“G” hole at front) on top of first GEO M10

Remove the the BL825 quick release pin of rear bumper link bar.

Connect bumper front points to GEO M10, front points will lock automatically

Connect the bumper link bar (0° position) to GEO M10 rear rigging plate (hole marked “bumper”) Lock
with the quick release pin BL0825.

Summary of Contents for GEO M10
















































































Search results

Summary of Contents for GEO M10

Reviews:

Related manuals for GEO M10

Brands by name

Popular brands

Nexo GEO M10, Setup Manual

Search results

Summary of Contents for GEO M10

Reviews:

Related manuals for GEO M10

Brands by name

Popular brands