manualshive.com logo in svg

Nexo GEO M10, Setup Manual

Share
Download
Nexo GEO M10 Setup Manual Download Page 56

Page 56/79 

GEO

 

M10

 HARDWARE SETUP PROCEDURE

 

 

 

 

 

 

 

 

 

- 

Once all MSUB15 are off the ground, position second VNT-BUMPM10 below last MSUB15 

- 

Pull bottom bumper front latches, and rotate the upper links so that single leg, and release the 
latches 

- 

Unlock last MS15SUB top front and rear rigging points 

- 

Connect bottom bumper to last MSUB15 by locking front and rear rigging points 

GEO M10 Left 

- 

Position first GEO M10 below bottom bumper so that Autorig

TM

 is at the bottom 

- 

Pull the bottom bumper front latches, rotate the lower links so that connection points are double leg 
and release the latches. 

- 

Position first GEO M10 below bottom bumper and lock front points to the bumper with 2 BL820 quick 
release pins. 

- 

Connect the bumper link bar at required angle (selection from -12° to +12° in 3° steps) to GEO M10 
rear rigging plate (hole marked “bumper”) and lock with the quick release pin BL0825. 

GEO M10 Right 

- 

Position first GEO M10 so that Autorig

TM

 is at the top and set in automatic lock position 

- 

Pull  the  bumper  front  latches,  rotate  the  lower  links  so  that  connection  points  are  single  leg  and 
release the latches. 

- 

Position bumper on top of first GEO M10, front points will lock automatically 

- 

Connect the bumper link bar at required angle (selection from -12° to +12° in 3° steps) to GEO M10 
rear rigging plate (hole marked “bumper”), and lock with the quick release pin BL0825. 

 

 

 

 

 

 

 

Summary of Contents for GEO M10
















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands