NexComm Systems NEXPEED NBG440 User Manual Download

Page: 117 / 125

NEXPEED NBG440 User’s Manual

NexComm Systems, Inc. 116 PAGE

Configuring NBG440(CO):

①

Use the console port for the configuration. Connect the CONSOLE port to a serial (COM) port

of your computer using the console cable (the enclosed cable in the box). Use a terminal

emulation program with the following parameters:

9600 bps, No parity, 8 data bits, 1 stop bit, NO flow control / VT100 terminal emulation

②

Power on the router and enter the password to log in the router. The default password is a

small letter “password”. If you log in the router, the login prompt

NBG440

> appears.

③

Enter

enable

command and the password to enter configuration mode. The default password is

a small letter “password”. The prompt changes to the configuration mode prompt

(conf)#

Configuration changes can be made only in configuration mode.

NBG440> enable

password:

NBG440(conf)#

④

Restoring the factory default settings and then log in the router again.

NBG440(conf)# write config –default

WARNING !!! this will overwrite the current setting:

Confirm ? (y/n)

=> enter y

NBG440(conf)# reboot flash

⑤

Set the device type, side and a line rate of each SHDSL port.

NBG440(conf)# device s0 gshdsl co auto 2320

NBG440(conf)# device s1 gshdsl co auto 2320

⑥

Set

Bridging mode

to the s0 and s1 interface.

NBG440(conf)# interface s0 bridge enable

NBG440(conf)# interface s1 bridge enable

⑦

Set the IP address of the LAN interface (for management). And remove

Routing

mode from

LAN interface. (If you don’t configure an IP address, skip this step.)

NBG440(conf)# interface lan ip 203.247.170.2 255.255.255.0

NBG440(conf)# ip routing disable lan

⑧

Set the default gateway (for remote management). (If you don’t configure the default gateway,

skip this step.)

NBG440(conf)# ip route add default lan 203.247.170.1

Summary of Contents for NEXPEED NBG440






























































































































Search results

Summary of Contents for NEXPEED NBG440

Reviews:

Related manuals for NEXPEED NBG440

Brands by name

Popular brands

NexComm Systems NEXPEED NBG440, User Manual

Search results

Summary of Contents for NEXPEED NBG440

Reviews:

Related manuals for NEXPEED NBG440

Brands by name

Popular brands