NexComm Systems NEXPEED NBG440 User Manual Download

Page: 100 / 125

NEXPEED NBG440 User’s Manual

NexComm Systems, Inc. 99 PAGE

Upgrading the System Software

The NBG440 unit can upgrade using TFTP (Trivial File Transfer Protocol). If a newer version of

the software for your NBG440 unit is available, you be sure to perform any required preparatory

tasks.

Preparing to upgrade

Before upgrading system firmware, be sure to confirm the following items.

For the file downloading, the program that supports TFTP server function should be

installed in the user's PC in advance.

And the binary (BIN) file to be downloaded should be saved in the user's PC.

This file is supported in the form of a binary file such as “nbg440.<version>.bin”.

The TCP/IP communication should be possible between the user's PC and the

NBG440 router.

Note1:

If you upgrade with the wrong file, the unit will not function and you will have

to return it for replacement.

Note2:

If you don’t have a firmware file(BIN file), you can download a file from

NexComm Homepage(http://www.nexcomm.co.kr) or contact NexComm sales or

technical support department.

Upgrading the system software

Step1:

Make sure the TFTP server is running. And place the firmware file in your TFTP

server’s root directory.

Step2:

To download the new binary image into the router, use the following command:

COMMAND

(conf)# tftp <host> <file>

Parameters

<host> - TFTP server’s IP address

<file> - Firmware file name

Note:

If the firmware file is not root directory, you must type full path to access the file.

Summary of Contents for NEXPEED NBG440






























































































































Search results

Summary of Contents for NEXPEED NBG440

Reviews:

Related manuals for NEXPEED NBG440

Brands by name

Popular brands

NexComm Systems NEXPEED NBG440, User Manual

Search results

Summary of Contents for NEXPEED NBG440

Reviews:

Related manuals for NEXPEED NBG440

Brands by name

Popular brands