Nexa CURTISS P-40 Instruction Manual Download Page 10

Page: 10 / 12

Firewall

A=A’

FRONT-VIEW

SIDE-VIEW

A’

121mm

To muffler

Filler tube

To engine

Rubber
stopper

Cap

Stopper

Fuel tube

After confirming the direction, insert this assembly,
clunk end first, into the fuel tank and tighten and
screw the fuel tank cap on firmly.

2.5x10mm.....4

SIDE VIEW

2mm

5mm

-Using a aluminum motor mounting plate as a template, mark the
fire-wall where the four holes are to be drilled (14A).

-Remove the aluminum motor mounting plate and drill a 13/64”(5mm)
hole through the fire-wall at each of the four marks marked (14B).

-Push the four 5x70mm bolts through the fire-wall.

-Reposition the aluminum motor mounting plate and secure it in place
with eight 5mm nuts and washers (14C).

Note: A=A’(side-view) and B=B’ (top-view)

Firewall

B=B’

TOP-VIEW

B’

! Engine thrust on balk head is already adjust at factory.

14A

14B

14C

5x70mm.......4

5mm nut.......12

5mm washer...16

3mm screw/nut...4

Li-po battery stand

In case of Electric motor using

11- Fuel tank & cowl

12- Electric motor

13- Lipo battery stand

Summary of Contents for CURTISS P-40













Search results

Summary of Contents for CURTISS P-40

Reviews:

Related manuals for CURTISS P-40

Brands by name

Popular brands

Nexa CURTISS P-40, Instruction Manual

Search results

Summary of Contents for CURTISS P-40

Reviews:

Related manuals for CURTISS P-40

Brands by name

Popular brands