manualshive.com logo in svg

NEX ROBOTICS FIREBIRD V ATMEGA 2560, Hardware Manual, Page: 4 / 121

Share
Download
NEX ROBOTICS FIREBIRD V ATMEGA 2560 Hardware Manual Download Page 4

Fire Bird V ATMEGA2560 Hardware Manual

Notice

The contents of this manual are subject to change without notice. All efforts have been made to 
ensure the accuracy of contents in this manual. However, should any errors be detected, NEX 
Robotics welcomes your corrections. You can send us your queries / suggestions at 

[email protected]

 

Content of this manual is released under the Creative Commence cc by-nc-sa license. For legal 
information refer to: 

http://creativecommons.org/licenses/by-nc-sa/3.0/legalcode

 

•

Robot’s electronics is static sensitive. Use robot in static free environment.

•

Read the hardware and software manual completely before using this robot

 

Recycling:

Almost all of the robot parts are recyclable. Please send the robot parts to the recycling plant 
after its operational life. By recycling we can contribute to cleaner and healthier environment for 
future generations.

© NEX Robotics Pvt. Ltd. and ERTS Lab, CSE, IIT Bombay, INDIA                                      4

Summary of Contents for FIREBIRD V ATMEGA 2560


























































































































Reviews:

No comments