background image

                                                                                   Part No. 803172 Issued 3-29-13 Rev 012015 

 

5.  Press QCD towards the dispensing 

spout until it is flush with the 
collar of the QCD. 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 
 
 
 
 
 

6.  The BIB should lie horizontally 

• 

Avoid loops in the product line 

• 

Use the minimum amount of 

product line required. 

• 

Check for air bubbles in the 

product line to trouble shoot for 
priming. 

 

PRIME SYSTEM 

7.  After the BIB has been connected to 

the QCD valve  dispense 
approximately 12 ounces of product. 

8.

 

Dispense another 8 ounces of  

     product and sample for taste. If  
     an adjustment is necessary refer to  
     taste calibration section page #7. 
NOTE:  Be sure there are no air 
bubbles  in the product line. 

 
 

 

 
 

 

Cleaning Instructions  

To clean and flush lines before connecting 
BIB product to unit or when changing 
product. Flush should be performed at least 
once a week. 

 

Note: 
Cleaning requires the use of a 
cleaning/flush adapter. An adapter may be 
purchased from Newco Enterprises, Inc. 
#320282 for QCD cleaning /flush adapter. 
#120508 for Scholle cleaning/flush adapter. 
A cleaning adapter can be made by taking 
an empty BIB bag and cutting away as 
much of the empty bag as possible. Wash 
the remaining connector and further trim 
off any remaining bag pieces if desired. 
This is now your cleaning adapter. It will 
allow the check valve in the connector to 
stay open during the cleaning process. 
Cleaning adapters may be saved for later 
use. 
1.  Connect clean/flush adapter to QCD 

or Scholle connector. 

2.  Place connector with adapter in 

container of hot water. 

3.  Lock or hold faucet handle down 

until clear water runs from faucet. 

4. Remove adapter from connector. 
5. Attach connector to new BIB. 

    
 

FLUSH POSITION 

Summary of Contents for 872DS












Reviews: