background image

2

XL-PS20053RM-en-US Rev A · 2017-10-06 · Amendments and Errors Reserved © SAF-HOLLAND, Inc., SAF-HOLLAND, HOLLAND, NEWAY, SAF, and logos are trademarks of  

SAF-HOLLAND S.A., SAF-HOLLAND GmbH, and SAF-HOLLAND, Inc.

Contents

Contents Page
Introduction ......................................................................... 2
Warranty .............................................................................. 2
Notes, Cautions, and Warnings ............................................. 2
Section 1 – Safety Instructions ............................................. 3
Service Repair Kits ............................................................... 4
Section 2 – LSZ13 Remove Lower Control Arm ..................... 8
Section 3 – LSZ13 Remove Upper Control Arm ...................... 8
Section 4 – LSZ20 Remove Lower Control Arm ..................... 9
Section 5 – LSZ20 Remove Upper Control Arm ...................... 9
Section 6 – LSZ13/20 Replacing Bushings ........................... 10 

Contents Page
Section 5 – LSZ20 Remove Upper Control Arm ...................... 9
Section 6 – LSZ13/20 Replacing Bushings ........................... 10
Section 7 –  LSZ13 Install New or Rebushed  

Lower Control Arm ........................................... 10

Section 8 –  LSZ13 Install New or Rebushed 

Upper Control Arm ........................................... 12

Section 9 –  LSZ20 Install New or Rebushed  

Upper Control Arm ........................................... 13

Section 10 –  LSZ20 Install New or Rebushed 

Lower Control Arm ......................................... 14

Section 11 – Torque Specification ....................................... 15

Notes, Cautions, and Warnings

Before starting any work on the unit, read and understand all 
the safety procedures presented in this manual. This manual 
contains the terms “NOTE”, “IMPORTANT”, “CAUTION”, and 
“WARNING” followed by important product information. These  
terms are defined as follows:

NOTE:

  Includes additional information to enable accurate 

and easy performance of procedures.

IMPORTANT:

  Includes additional information that  

if NOT followed could lead to hindered  
product performance.

Used without the safety alert symbol,  
indicates a potentially hazardous 
situation which, if not avoided, could 
result in property damage.

Indicates a potentially hazardous 
situation which, if not avoided, could 
result in minor or moderate injury.

Indicates a potentially hazardous 
situation which, if not avoided, could 
result in death or serious injury.

Introduction

This manual provides the necessary information for the 
maintenance, inspection, and safe operation of the NEWAY

®

 

LSZ Series Auxiliary Air Suspension.

NOTE:

  To assist with installation, customer inspection 

drawing LSZ13_TAB_CI is required and is included  
in the literature kit.

Read this manual before using or servicing this product and  
keep it in a safe location for future reference. Updates to this 
manual, which are published as necessary, are available on 
the internet at www.safholland.us.

When replacement parts are required, SAF-HOLLAND

®

 highly 

recommends the use of only SAF-HOLLAND Original Parts.  
A list of technical support locations that supply SAF-HOLLAND 
Original Parts and an Aftermarket Parts Catalog are available 
on the internet at www.safholland.us or contact Customer 
Service at 888-396-6501.

Warranty

Refer to the complete warranty for the country in which  
the product will be used. A copy of the written warranty  
is included with the product or available on the internet  
at www.safholland.com.

Summary of Contents for LSZ13

















Reviews: