manualshive.com logo in svg

New Yorker CL3-105, Installation, Operating And Service Instructions, Page: 53 / 64

Share
Download
New Yorker CL3-105 Installation, Operating And Service Instructions Download Page 53

53

Item 

No. Description

Boiler Size / Quantity

Part No.

CL3

CL4

CL5

Bare Boiler Assembly

1

Front Section (Non-Htr.), Machined Water

---(OR)---

Front Section (Non-Htr.), Machined Steam

1

1

1

71720103
71720104

2

Center Section

1

2

3

71720301

3

Rear Section (Non-Htr.), Machined Water

---(OR)---

Rear Section (Non-Htr.), Machined Steam

1

1

1

71720201
71720202

Rear Heater Section, Machined Water

---(OR)---

Rear Heater Section, Machined Steam

71720203
71720204

4

5" Cast Iron Slip Nipple

2

3

4

7066003

5

Slip Nipple, 22-B Steel

2

3

4

806600375

6

Rear Target Wall Insulation

1

1

1

82020002

7

Tie Rod, 3/8"-16 x 12-1/2" Lg.

2

---

---

80861010

Tie Rod, 3/8"-16 x 17-3/4" Lg.

---

2

---

80861032

Tie Rod, 3/8"-16 x 23" Lg.

---

---

2

80861049

8

3/8" Flat Washer

4

4

4

80860600

9

3/8"-16 Hex Nut

4

4

4

80860423

10

Combustion Chamber Liner, 1/2" x 19-1/2" x 9-3/4"

1

---

---

82020031

Combustion Chamber Liner, 1/2" x 19-1/2" x 14-3/4"

---

1

---

82020041

Combustion Chamber Liner, 1/2" x 19-1/2" x 19-3/4"

---

---

1

82020051

11

BSD Hinge Loop Bracket

2

2

2

100795-02

12

5/16" Flat Washer - Plated

4

4

4

80860611

13

5/16-18 x 1" Lg. Cap Screw, Plated

2

2

2

80861341

14

5/16-18 x 1-1/2" Lg. Cap Screw, Plated

2

2

2

80861349

15

Burner Swing Door (only), Machined / Painted

1

1

1

100793-01

16

Burner Swing Door Insulation

1

1

1

82020001

17

Observation Port Cover, Machined / Painted

1

1

1

71728004

18

5/16-18 x 3/4" Lg. Cap Screw, Plated

1

1

1

80861340

19

Canopy Sealing Strip (1/2" x 1-1/4" x 10') in Poly Bag

1

1

1

6206001

20

Canopy Assembly - 3 Section, 5-7/8" Dia. Collar

1

---

---

100827-03

Canopy Assembly - 4 Section, 6-7/8" Dia. Collar

---

1

---

100827-04

Canopy Assembly - 5 Section, 7-7/8" Dia. Collar

---

---

1

100827-05

21

1/4"-20 x 3" Lg. Carriage Bolt, Plated

2

2

2

80860119

22

1/4"-20 x 3-1/2" Lg. Carriage Bolt, Plated

2

2

2

100838-01

23

1/4" Flat Washer - Plated

4

4

4

80860603

24

1/4"-20 Wing Nut - Plated

4

4

4

80860910

25

Heater Cover Plate Gasket - Rear Heater

1

1

1

8036058

26

V1-2 Heater Carton (WT[R] & ST[R]) Rear Heater

1

1

1

6036031

27

5/16" Flat Washer - Plated

8

8

8

80860611

28

3/8"-16 x 7/8" Lg. Cap Screw, ASME Grade, Marked  SA307B

8

8

8

80861337

X:  REPAIR PARTS (continued)

Summary of Contents for CL3-105

































































Reviews:

No comments