manualshive.com logo in svg

New Yorker CL3-105, Installation, Operating And Service Instructions, Page: 13 / 64

Share
Download
New Yorker CL3-105 Installation, Operating And Service Instructions Download Page 13

13

ii.

  Remove existing nozzle from nozzle adapter.

iii.

   Insert the proper NOZZLE into NOZZLE 

ADAPTER and tighten securely (

DO NOT

 

cover tighten), refer to Table 14B (at rear of 

this manual).

iv. 

Replace adapter, with nozzle installed, into  

drawer assembly and secure with screw (1).

c. 

Inspect and measure burner electrodes

.  Refer 

to Figure 7 for the proper electrode settings.

d.

  Re-install Drawer Assembly

 

into Combustion 

Head

 per Step 3a above.

e. 

Insertion Depth, 

verify the distance between 

the tip of the end cone is equal to the distance 

specified in Table 14B (at rear of this manual).

f. 

Turbulator Setting

, refer to Figure 8.

Figure 6:  Riello Nozzle Replacement

III:  INSTALLATION INSTRUCTIONS (continued)

Figure 5:  Installation/Removal of

Riello Drawer Assembly

Figure 7:  Riello Electrode Setting

Figure 8:  Riello Turbulator Setting

l.  Inspect Beckett head setting on left side of 

burner by insuring the line on the label MB(L1) 

or the blue line MD(V1) are aligned, readjust if 

necessary.  Refer to Figure 26.

m. Tighten knurled nut.
n.  Swing igniter closed, rotate tabs and tighten two 

(2) igniter screws.

3.  ON THE RIELLO 40 SERIES OIL BURNER, use 

the following procedure to complete the inspection, 

check the settings and to change the nozzle to a 

lower firing rate:   Refer also to 

Model F3 & F5 

Installation Manual, Riello 40 Series Residential 

Oil Burners

 (C6501010) or 

Model F10 Installation 

Manual, Riello 40 Series Residential Oil Burners

  

No. 2902554.
a. 

Installation/Removal of Drawer Assembly

, 

refer to Figure 5.

i.

   Removal:

 

•  Disconnect oil delivery tube nut from  

 pump.

 

•  Loosen SCREW (3), and then unplug  

  PRIMARY CONTROL (1) by carefully  

  pulling it back and then up.

 

•  Remove the AIR TUBE COVER    

  PLATE (5) by loosening the retaining  

  SCREW (4) (Two SCREWS-Model F5).

 

•  Loosen SCREW (2), and then slide the  

  complete drawer assembly out of the  

    combustion head as shown.

ii.

   Installation:

   To insert drawer assembly, reverse the   

procedure in Step

 i

 above.

b. 

Nozzle Replacement

, refer to Figure 6.

i.

   Remove the NOZZLE ADAPTER (2) from 

the DRAWER ASSEMBLY by loosening 

the SCREW (1).

Summary of Contents for CL3-105

































































Reviews:

No comments