New Yorker CL3-105 Installation, Operating And Service Instructions Download Page 47

Page: 47 / 64

Important Product Safety Information

Refractory Ceramic Fiber Product

Warning

The Repair Parts list designates parts that contain refractory ceramic fibers

(RCF). RCF has been classified as a possible human carcinogen. When

exposed to temperatures about 1805°F, such as during direct flame contact,

RCF changes into crystalline silica, a known carcinogen. When disturbed as a

result of servicing or repair, these substances become airborne and, if inhaled,

may be hazardous to your health.

AVOID Breathing Fiber Particulates and Dust

Precautionary Measures

Do not remove or replace RCF parts or attempt any service or repair work

involving RCF without wearing the following protective gear:

1. A National Institute for Occupational Safety and Health (NIOSH)

approved respirator

2. Long sleeved, loose fitting clothing
3. Gloves
4. Eye Protection

• Take steps to assure adequate ventilation.
• Wash all exposed body areas gently

with soap and water after contact.

• Wash work clothes separately fr

om other laundry and rinse washing

machine after use to avoid contaminating other clothes.

• Discard used RCF components by sealin

g in an airtight plastic bag. RCF

and crystalline silica are not classified as hazardous wastes in the United

States and Canada.

First Aid Procedures

• If contact with eyes: Flush with wa

ter for at least 15 minutes. Seek

immediate medical attention if irritation persists.

• If contact with skin: Wash affect

ed area gently with soap and water.

Seek immediate medical attention if irritation persists.

• If breathing difficulty develops: Leave the area and move to a location

with clean fresh air. Seek immediate medical attention if breathing

difficulties persist.

• Ingestion: Do not induce vomiting.

Drink plenty of water. Seek

immediate medical attention.

Summary of Contents for CL3-105

































































Search results

Summary of Contents for CL3-105

Reviews:

Related manuals for CL3-105

Brands by name

Popular brands

New Yorker CL3-105, Installation, Operating And Service Instructions

Search results

Summary of Contents for CL3-105

Reviews:

Related manuals for CL3-105

Brands by name

Popular brands