New Holland H8060 Service Manual Download Page 19 | Manualshive

Page: 19 / 51

background image

INTRODUCTION

Personal safety - Do not operate tag

WARNING

Avoid injury! Always do the following before lubricating, maintaining, or servicing the machine.
1. Disengage all drives.
2. Engage parking brake.
3. Lower all attachments to the ground, or raise and engage all safety locks.
4. Shut off engine.
5. Remove key from key switch.
6. Switch off battery key, if installed.
7. Wait for all machine movement to stop.
Failure to comply could result in death or serious injury.

W0047A

Before you service the machine, put a DO NOT OPERATE tag on the instrument panel.

321_4614

1

DO NOT OPERATE TAG

A.

(1)

Do not operate.

B.

(2)

Do not remove this.

C.

(3)

See other side.

D.

(4)

Signed by.

E.

(5)

Reason

The DO NOT OPERATE tag can be obtained from your NEW HOLLAND AGRICULTURE dealer.

47487696 17/01/2013

15

«
...
17
18
19
20
21
...
»

Summary of Contents for H8060




















































Reviews:

No comments

Related manuals for H8060

Brand: ABB Pages: 18

Brand: R-Tech Pages: 3

Brand: Unex Pages: 5

Brand: Fisher Scientific Pages: 42

Brand: IBS Scherer Pages: 64

Brand: Hagerman Pages: 4

Brand: hager Pages: 2

TECSHOW QUAD SPIDER 60

Brand: Ampro Pages: 9

Brand: JB-Lighting Pages: 32

Brand: W&H Pages: 72

Brand: Major tech Pages: 12

Brand: Bartscher Pages: 20

Brand: Bartscher Pages: 24

Brand: H&S Pages: 32

Brand: Pani Pages: 12

Brand: FASTER TOOLS Pages: 19

Brand: Task Force Tips Pages: 16

Brand: Osram Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands