netsys NH-800SP User Manual Download Page 72

Page: 72 / 81

NH-800SP 8 PORTS Managed HPNA IP DSLAM USER’S MANUAL Ver_B2

enjoy internet service, you must change a Router with higher session numbers to overcome that.

System Diagnostics

Power and Cooling Problems

If the POWER indicator does not turn on when the power cord is plugged in, you may have a problem with the power outlet,

power cord, or internal power supply as explained in the previous section. However, if the unit should turn itself off after

running for a while, check for loose power connections, power losses or surges at the power outlet, and verify that the fan on

back of the unit is unobstructed and running prior to shutdown. If you still cannot isolate the problem, then the internal power

supply may be defective. In this case, contact your supplier for assistance.

Installation

Verify that all system components have been properly installed. If one or more components appear to be malfunctioning (e.g.,

the power cord or network cabling), test them in an alternate environment where you are sure that all the other components are

functioning properly.

Transmission Mode

The selections of the transmission mode for the RJ-45 ports are auto-negotiation using the default method. Therefore, if the Link

signal is disrupted (e.g., by unplugging the network cable and plugging it back in again, or by resetting the power), the port will

try to reestablish communications with the attached device via auto-negotiation. If auto-negotiation fails, then communications

are set to half duplex by default. Based on this type of industry-standard connection policy, if you are using a full-duplex device

that does not support auto-negotiation, communications can be easily lost (i.e., reset to the wrong mode) whenever the attached

device is reset or experiences a power fluctuation. The best way to resolve this problem is to upgrade these devices to version

Summary of Contents for NH-800SP


















































































Search results

Summary of Contents for NH-800SP

Reviews:

Related manuals for NH-800SP

Brands by name

Popular brands

netsys NH-800SP, User Manual

Search results

Summary of Contents for NH-800SP

Reviews:

Related manuals for NH-800SP

Brands by name

Popular brands