netsys NH-800SP User Manual Download Page 68

Page: 68 / 81

NH-800SP 8 PORTS Managed HPNA IP DSLAM USER’S MANUAL Ver_B2

TIP:

1. Verify that the cable type is correct. Be sure RJ-45 cable connectors are securely seated in the required ports. Use

100

Ω

straight-through cables for all standard connections. Use Category 5 cable for 100Mbps Fast Ethernet

connections, or Category 3, 4 or 5 cables for standard 10Mbps Ethernet connections. Be sure RJ-11 phone wiring, use

18~26 gauge.

2. Make sure all devices are connected to the network. Equipment any have been unintentionally disconnected from the

network.

3. When cascading two devices using RJ-45 station ports at both ends of the cable (i.e., not an MDI port), make sure a

crossover cable is used. Crossover cable should only be used if a MDI port is not available.

Summary of Contents for NH-800SP


















































































Search results

Summary of Contents for NH-800SP

Reviews:

Related manuals for NH-800SP

Brands by name

Popular brands

netsys NH-800SP, User Manual

Search results

Summary of Contents for NH-800SP

Reviews:

Related manuals for NH-800SP

Brands by name

Popular brands