netsys NH-800SP User Manual Download

Page: 66 / 81

NH-800SP 8 PORTS Managed HPNA IP DSLAM USER’S MANUAL Ver_B2

Appendix A:

Cable Requirements

A CAT 3, 4 or 5 UTP (unshielded twisted pair) cable is typically used to connect the Ethernet device to the modem. A

10Base-T cable often consists of four pairs of wires, two of which are used for transmission. The connector at the end of the

10Base-T cable is referred to as an RJ-45 connector and it consists of eight pins. The Ethernet standard uses pins 1, 2, 3

and 6 for data transmission purposes. (

Table A-1

)

Table A-1 RJ-45 Ethernet Connector Pin Assignments

MDI

MDI-X

PIN #

Signal

Media Dependant

interface

Signal

Media Dependant

interface-cross

TX+

Transmit Data +

RX+

Receive Data +

TX-

Transmit Data -

RX-

Receive Data -

RX+

Receive Data +

TX+

Transmit Data +

Unused

RX-

Receive Data -

TX-

Transmit Data -

Unused

Figure A-1 Standard RJ-45 repectacle/connector

Note:

Please make sure your connected cables are with same pin assignment as above table before deploying the cables into your

network.

Summary of Contents for NH-800SP


















































































Search results

Summary of Contents for NH-800SP

Reviews:

Related manuals for NH-800SP

Brands by name

Popular brands

netsys NH-800SP, User Manual

Search results

Summary of Contents for NH-800SP

Reviews:

Related manuals for NH-800SP

Brands by name

Popular brands