NETGEAR ProSafe FS750T2 User Manual Download Page 20

Page 20 of 21 

APPENDIX C: TECHNICAL SPECIFICATIONS

 

This appendix provides technical specifications for the NETGEAR ProSafe FS750T2 Smart Switch. 

Network Protocol and Standards Compatibility

 

IEEE 802.3 10BASE-T  
IEEE 802.3u 100BASE-TX  
IEEE 802.3ab 1000BASE-T 
IEEE 802.3z 1000Base-X 
IEEE 802.3x flow control 

 

Management

 

IEEE 802.1Q Static VLAN (Up to 64) 
Port-based VLAN (Up to 50)

 

IEEE 802.1p Class of Service (CoS)   
Port-based QoS (options High/Normal/Low/Lowest) 
Port Trunking - Manual as per IEEE802.3ad Link Aggregation 
Port Monitoring 
IEEE 802.1D Spanning Tree Protocol (Q2 2005) 
RFC 1157 SNMP v1 (Q2 2005) 

 

Interface

 

48 RJ-45 connectors for 10BASE-T, 100BASE-TX (Auto Uplink. on all ports) 
2 RJ-45 connectors for 10BASE-T, 100BASE-TX and 1000BASE-T (Auto Uplink. on both ports) 
2 SFP GBIC module bays that share with 2 Gigabit RJ45 ports for fiber connectivity

 

 

LEDs

 

Per port (10/100 Mbps): Speed (dual color), Link, Activity 
Per port (10/100/1000 Mbps TP): Speed (dual color), Link, Activity 
Per port (SFP port): Link, Activity  
Per device: Power 

 

Performance Specifications

 

Forwarding modes: Store-and-forward 
Bandwidth: 13.6 Gbps 
Network latency: Less than 20 microseconds for 64-byte frames in store-and-forward mode for 100 Mbps to 100 Mbps transmission 
Buffer memory: 128 KB embedded memory per unit 
Address database size: 8,000 media access control (MAC) addresses per system 
Mean Time Between Failure (MTBF): 59,880 hours (~ 6.8 years) 

 

Power Supply 

Power Consumption: 21 W maximum 
100-240VAC/50-60 Hz universal input 

 

Physical Specifications

 

Dimensions (H x W x D): 1.7 x 17.3 x 8.1 in (43.2 x 440 x 205 mm)  
Weight:

 

6.88 lbs. (3.13 Kg) 

 

Environmental Specifications

 

Operating temperature: 0 to 40°C (32 to 104°F) 
Storage temperature: -20 to 70°C (-4 to 158°F) 
Operating humidity: 90% maximum relative humidity, non-condensing 
Storage humidity: 95% maximum relative humidity, non-condensing 
Operating altitude: 3,000 m (10,000 ft) maximum 
Storage altitude: 3,000 m (10,000 ft) maximum 

 

Electromagnetic Emissions

 

CE mark, commercial  
FCC Part 15 Class A  
VCCI Class A  
C-Tick 
  

Electromagnetic Immunity

 

EN 55024:1998 +A1:2001

 

 

Safety

 

CE mark, commercial 
cUL 60950 (Listed)/ EN60950 (Low Voltage Directive) 
 

Summary of Contents for ProSafe FS750T2






















Reviews: