NETGEAR Nighthawk CAX30 User Manual Download Page 12

Page: 12 / 140

Table 1. LED descriptions (Continued)

• Solid white. The 2.4 GHz WiFi radio is operating.

• Blinking. The router is sending or receiving WiFi traffic.

• Off. The 2.4 GHz WiFi radio is off.

2.4 GHz radio

• Solid white. The 5 GHz WiFi radio is operating.

• Blinking. The router is sending or receiving WiFi traffic.

• Off. The 5 GHz WiFi radio is off.

5 GHz radio

• Solid white. A USB device is connected and is ready.

• Solid amber. A USB device is connected and is ready.

• Off. No USB device is connected, or someone clicked the Safely

Remove Hardware button and it is now safe to remove the attached
USB device.

USB port

The WiFi and WPS buttons are located on the front of the modem router.

Table 2. Front panel buttons

Description

Button

Pressing this button for two seconds turns the WiFi radios in the modem
router on and off. If this LED is lit, the WiFi radios are on. If this LED is off,
the WiFi radios are turned off and you cannot use WiFi to connect to the
modem router.

WiFi

This button lets you use WPS to join the WiFi network without typing the
WiFi password. The WPS LED blinks during this process and then lights
solid.

WPS

Rear Panel

The connections and button on the rear panel are shown in the following figure.

User Manual

Hardware Setup

Nighthawk AX6 AX2700 WiFI Cable Modem Router Model CAX30

Summary of Contents for Nighthawk CAX30













































































































































Search results

Summary of Contents for Nighthawk CAX30

Reviews:

Related manuals for Nighthawk CAX30

Brands by name

Popular brands

NETGEAR Nighthawk CAX30, User Manual

Search results

Summary of Contents for Nighthawk CAX30

Reviews:

Related manuals for Nighthawk CAX30

Brands by name

Popular brands