NETGEAR MS108EUP Hardware Installation Manual Download Page 4 | Manualshive

Page: 4 / 30

NETGEAR MS108EUP Hardware Installation Manual Download Page 4

Contents

Chapter 1 Introduction

Overview................................................................................................6
Features.................................................................................................6
Safety instructions and warnings........................................................7

Chapter 2 Hardware Overview

Front panel with ports and LEDs......................................................12
LEDs......................................................................................................13
Back panel...........................................................................................14
RJ-45 ports for 100/1000/2.5GBASE-T Ethernet connectivity......14
Reset / Factory Defaults button........................................................15

Chapter 3 Applications

PoE++ and PoE+ overview................................................................17
PoE++ and high-speed desktop switching.....................................18

Chapter 4 Installation

Step 1: Prepare the site......................................................................20
Step 2: Protect against electrostatic discharge..............................20
Step 3: Unpack the switch.................................................................21
Step 4: Install the switch....................................................................22

Install the switch on a flat surface.................................................22
Wall-mount the switch horizontally..............................................22
Wall-mount the switch vertically...................................................24
Mount the switch to a pole or another surface..........................24

Step 5: Connect devices to the switch.............................................25
Step 6: Check the installation...........................................................25
Step 7: Apply power and check the LEDs.......................................26
Step 8: Manage the switch................................................................26

Chapter 5 Troubleshooting

Troubleshooting chart.......................................................................28
PoE troubleshooting suggestions....................................................29
Additional troubleshooting suggestions.........................................30

4

«
...
2
3
4
5
6
...
»

Summary of Contents for MS108EUP































Reviews:

No comments