NetComm VELOCITY NP805N User Manual Download Page 8

Page: 8 / 62

NP805N – Gigabit Wireless Router

NetComm NP805N - Gigabit Wireless Router

YMLO-805N

www.netcomm.com.au

Integrated Interfaces

The following integrated interfaces are available on the NP805N:

REAR PANEL

INTERFACE

FUNCTION

WIFI Antenna

Connect one of the supplied WIFI antennas here; It should be screwed on in a clockwise direction.

LAN 1-4

Connect Ethernet based devices here

WAN

Connect an Ethernet based WAN device here

Power Jack

Connect the power supply here

Power button

Power the NP805N on or off

WIFI Antenna

Connect one of the supplied WIFI antennas here; It should be screwed on in a clockwise direction.

FRONT PANEL

INTERFACE

FUNCTION

USB

Connect a USB storage based device here to provide access to connected clients.

RESET

Press and hold the reset button for 5 seconds to restore the NP805N to Factory Defaults.

WPS / USB OFF

Press for WPS mode

Hold for 5 seconds to disable the USB functionality.

Summary of Contents for VELOCITY NP805N































































Search results

Summary of Contents for VELOCITY NP805N

Reviews:

Related manuals for VELOCITY NP805N

Brands by name

Popular brands

NetComm VELOCITY NP805N, User Manual

Search results

Summary of Contents for VELOCITY NP805N

Reviews:

Related manuals for VELOCITY NP805N

Brands by name

Popular brands