manualshive.com logo in svg

NetApp 42U 1280 mm System Cabinet, Manual

Share
Download
NetApp 42U 1280 mm System Cabinet Manual Download Page 25

2

1

press

a.  Lift the retaining pin on the power supply housing, and then remove the housing cover by

rotating it downward and lifting it off the rear power supply housing.

Note: 

The power supply is attached to the power supply housing with a hook and loop

patch.

b.  Disconnect the power supply from the illuminated badge cable, and then set the power supply

and power supply cover to the side.

c.  Remove the screws from the top and bottom of the power supply housing that is attached to

the system cabinet frame, and then remove the power supply housing.

3.  Install the power supply and power supply housing on the opposite side of the system cabinet:

a.  Locate the two screw holes next to each other on the cabinet frame, and then attach the top of

the power supply housing to the bottom-most of the two screw holes.

Note: 

You might need to remove the bottom cable retention strap, if present.

b.  Secure the bottom of the power supply housing to the system cabinet frame.

c.  Install the power supply cover and power supply by aligning the cover hooks with the power

supply back, pulling the plunger up on the cover, rotating the plunger closed, and then
releasing the plunger.

Reversing the system cabinet front door | 25

Summary of Contents for 42U 1280 mm System Cabinet




































Reviews:

No comments

Brands by name

Popular brands

Load more brands