Ness D16xD Installer Manual Download Page 6

Page: 6 / 96

esD WArning

(electrostatic Discharge).
Once properly installed, Ness control
panels are well protected from eSD.
However, take note of the following
precautions during installation.
The human body can generate static
electricity when it is insulated from earth
- for instance by walking over carpet.
eSD occurs (and a small shock is
sometimes felt) if an earthed metal
object is then touched.
The installer should be aware that if
he generates static electricity while
installing the panel and then discharges
this static electricity into the internal
components on the main D8/D16 circuit
board or the keypad board, then eSD
damage may occur.
The circuit board should not be
unwrapped until it is actually ready to be
installed.

Methods to avoid electrostatic build-up.
1. Use a foot strap, a wrist strap,

or a grounding mat. The aim is
to connect the body to earth to
discharge static before it builds up.
The connection is a high resistance
for personnel safety.

2. If the above is not available, then it

is advisable to wear clothing that will
minimise the build-up of static.

3. Handle circuit boards by the edges.

Avoid touching any components on
the board as the integrated circuits,
in particular, are not guaranteed by
their manufacturers to be safe from
eSD.

4. To minimise the build-up of static,

avoid walking around as much
as possible while working on the
installation.

5. Touch an earthed object to

discharge any static before working
on the installation.

RECEIVER

LISTEN

SERIAL

READER

PROG

AMP

TERY

RED +

TELEPHONE

HEATSINK

AUX1

AUX2
AUX3
AUX4

+12V

TAMP

+12V

CLK

DAT

COM

RESET

STR

SIREN

17V

EARTH

BLACK

Up to 2 x Ness 12V Siren (100-172)
OR 3 x 12V Screamer (100-238, 100-004)

Up to 2 x Strobe Light (NOI-300)

Up to 3 x Horn Speaker, 8 Ohm (NOI-110)

Ness 17V AC Plug Pack
(Australia only)

+12V

CLK

DAT

NESS LCD Keypad

COM

Maximum
3 keypads

BOX TAMPER
SWITCH
N.C. Contacts
(WHITE)

J1 LINK

BOX TAMPER

PROGRAM LINK

= Sealed, normal state
= Tamper alarm state

Power up with link off to enter
installer program mode

BATTERY LEADS
(supplied)

“HEARTBEAT” LED

Constantly flashes

D8 MAIN BOARD

Ness OUTPUT EXPANDER

Part No. 106-011

Zone 2

Zone 6

Zone 4

Zone 8

Zone 7

Zone 1

Zone 5

Zone 3

2k2

N.O TAMPER SWITCH
(761-002) Colour: BLACK
Supplied with Ness siren covers

N.C TAMPER SWITCH (SWI920) Colour: WHITE

ALTERNATIVE TAMPER SWITCH WIRING
For N.C. Tamper Switches

To Aux Header

Part No. 106-012

Aux

Header

The Relay Board provides 4 relay
outputs suitable for switching low
voltageaccessories such as electric
strikes.
NOTE: Electric strikes must

not

Up to 3 addressable Weigand
readers

can

connec

via the optional 3 way

Reader Interface.

(Ness 101-014)

ted

Used for direct connect
to a PC for programming
or two way serial comms.

Connect

one

additional

expander

TO
HEADER

RECEIVER

header

READER

header

SERIAL

PC serial
port

NORMALLY OPEN
(

DEVICES

N.O.)

NORMALLY CLOSED
(

DEVICES

N.C.)

ZONE WIRING

ZONES 1-8

Zone

ZONES 1-8

Zone

RADIO INTERFACE

ess

Part No. 100-200

SERIAL CABLE

ess

Part No. 450-185

RELAY BOARD

ess

Part No. 106-013

OPTIONAL ACCESSORIES FOR D8

& D16

WEIGAND READER INTERFACE

+12V

DA
TA

White

RS
SI

Blue

Black

LISTEN PINS

Diagnostics. Connect an
8 Ohm horn speaker to
listen to dialler tones.

END OF LINE RESISTORS

The default end of line resistor value is 2k2 (2200 Ohms). The EOL value
is fully programmable with a choice of 13 resistor values, see program
option P129E.
Ness panels are supplied with 2k2 1% tolerance Metal Film resistors.
Colour code: Red, Red, Black, Brown, Brown.

TELEPHONE LEAD (Supplied)
Connect to Mode3 socket
Lead shown is for Australia only.

BATTERY CONNECTION

For 12V 7Ah backup
battery (BAT210)

RECEIVER

Header for
connecting
optional Radio
Interface.

AUX

Aux outputs
1-4.

SERIAL

Rs232 serial port

READER

Connection for
up to 3 Ness
Weigand readers

OUT

12V

+12V

AUX4

AUX3

AUX2

AUX1

NO C

AUX1

NC NO C

AUX2

NO C

AUX3

NC NO C

AUX4

Blu

Brn

Grn

Wht

Red

Blk

17V AC
(White & Black)

EARTH
(Yellow/Green stripe)

programmable

open

collector

outputs

12V DC output for detectors. Auto Reset fuse protected.
500mA max. from all 12V outputs.

12V DC output

instAllAtion ProCeDUres

The main panel housing and keypad/s should be installed within areas that are
protected by motion sensors or reed switches. A linen closet or cupboard are good
examples as these are generally located in the centre of the premises. Installing in
ceiling spaces or other areas where extremes of temperature may be encountered is
not advised.
Positioning of the movement detectors should be considered as the incorrect position
may cause unwanted alarms. Refer to the motion sensors' installation instructions.
1.   Remove the lid and the battery from the base.
2.   Securely mount the rear panel housing in a secure location.
3.   Run all cabling needed for the installation.
4.   Insert the red PCB stand-offs in the housing and then plug the circuit board onto

the stand-offs. See the eSD Warning on this page.

5. Wire the sensors, sirens and accessories to the main board terminal blocks as per

the wiring instructions shown in this installation manual.

6.  Fit the battery into the housing but DO NOT CONNeCT the battery yet.
7.  Insert the panel tamper bracket leads as shown below.
8.  Power up as described below.
9.  Close the lid and program the panel as required.

PoWer-UP ProCeDUre

To enter INSTAlleR PROGRAM MODe the first time, power-up with the PROG/TAMP
link OFF. If the PROG/TAMP link is ON and any other 24hr zones are unsealed on
power-up the panel will immediately go into alarm - reset the alarm via keypad or
remove power to stop the alarm.

1. ConneCt tHe bAttery First.

Observe correct polarity.

a) The heartbeat leD will flash continuously to indicate correct operation.
b) The Current limiting Globes should be OFF. If the Globes are glowing, the

battery connection is reversed. Immediately disconnect the battery and check the
polarity of the battery leads.

2. tUrn on tHe externAl PoWer sUPPly.

The Current limiting Globes may

glow slightly to indicate that the battery is charging correctly.

If the heartbeat leD does not flash steadily or cycles off intermittently there may be a
problem with the initialisation of the onboard memory.

to remedy, in installer Program

mode press P95e, P97e & P98e to erase all programming and reload factory defaults

Then remove power by briefly removing one of the battery leads then re-connect. The
heartbeat leD should now be flashing continuously, proceed to step 2.

NeSS D8X / D16X DelUXe CONTROl PANel – INSTAllATION MANUAl

NOTe:
your panel has a dual 17VAC/20VDC power input.
Please use the correct power supply as shown on
page 8

Insert the white N/C tamper switch

Insert the four red PCB
posts in the positions
shown

D8XD or D16XD
pcb

Backup battery holder.
Suits up to 12V 7Ah battery.

17VAC or

20VDC

Power InPut

non-PolArIty