Nespresso Gran Maestria EF 287 Service Manual Download

Page: 83 / 162

Maestria / Gran Maestria service manual

R E P A I R S

7.5.5 Replacing milk regulator assembly

•

Unplug connector for milk regulator (821) from electronic mainboard (806).

•

Remove 3 cable clips (111) from holder (1) by pressing the retention latches
inwards.

•

Loosen 3 screws (TX 10) and remove milk regulator (821).

Assembly checkpoint

•

Use cable guides on holder for milk regulator (77) and cable clips (111) to secure
wires.

7.5.6 Reassembly and wiring instructions - Gran Maestria

Reassembly checkpoints

•

Check if light guide (115) is mounted before attaching upper part of housing (114).

•

Check if permanent magnet (142) for drip tray is inserted in base (141). Remove
mounting aid (additional magnet) if present.

•

Take care not to jam any wires between base and upper part (especially wiring of
electronic main board).

821

111

Do not lose cable
clips!

Summary of Contents for Gran Maestria EF 287



































































































































































Search results

Summary of Contents for Gran Maestria EF 287

Reviews:

Related manuals for Gran Maestria EF 287

Brands by name

Popular brands

Nespresso Gran Maestria EF 287, Service Manual

Search results

Summary of Contents for Gran Maestria EF 287

Reviews:

Related manuals for Gran Maestria EF 287

Brands by name

Popular brands