Nespresso Gran Maestria EF 287 Service Manual Download

Page: 57 / 162

Maestria / Gran Maestria service manual

R E P A I R S

•

Remove flow meter hose from water tank connector (see “Replacing water tank
connector” on page 47).

•

Unlatch lower pump holder (14 / 196): Insert screwdriver blade into gap between
pump holder and holder (1). Then swivel screwdriver and move out pump assembly
with flow meter (22) partly.

•

Remove upper pump holder (15 / 197): Press in both wedges one after another with
a screwdriver and pull out upper pump holder from the machine.

•

Disconnect the cable from flow meter (22) and remove the pump assembly
completely.

Upper (15 / 197) and
lower (14 / 196) pump
holders have stop-

pers and latches.

14
(196)

15
(197)

Summary of Contents for Gran Maestria EF 287



































































































































































Search results

Summary of Contents for Gran Maestria EF 287

Reviews:

Related manuals for Gran Maestria EF 287

Brands by name

Popular brands

Nespresso Gran Maestria EF 287, Service Manual

Search results

Summary of Contents for Gran Maestria EF 287

Reviews:

Related manuals for Gran Maestria EF 287

Brands by name

Popular brands