background image

9.3 

Venting the installation

Any air in the appliance, the pipes or the valves must be removed in order 

to prevent annoying noises that may occur during heating or when tapping 

water. Proceed as follows:

1. Open the valves of all the radiators connected to the installation.

2. Set the room thermostat to the highest possible temperature.

3. Wait until the radiators are warm.

4. Switch off the boiler.

5. Wait approximately ten minutes, until the radiators feel cold.

6. Vent the radiators. Work from the bottom to the top.

7. Open the venting valve with the bleed key, keeping a cloth pressed 

against the vent.

8. Wait until water comes out of the venting valve and then close the 

venting valve. 

Warning

The central heating water may still be hot.

9. Switch the boiler on. 

A three-minute venting cycle is performed automatically.

10. After venting, check that the water pressure in the installation is still 

adequate. 

Important

If the water pressure is lower than 0.8 bar, the water must be top­

ped up. If necessary: top up the central heating installation (rec­

ommended water pressure between 1.5 and 2.0 bar).

11. Set the room thermostat or the control.

Fig.51

Venting the installation

AD-3000484-B

8

7

A

C

B

6

5

4

3

2

1

2

3

4

1

11

9  Maintenance

7628792 - v03 - 25072017

EF

35

Summary of Contents for EcoNox EF 22













































Reviews: