manualshive.com logo in svg

Neousys Nuvo-7160GC Series, User Manual

Share
Download
Neousys Nuvo-7160GC Series User Manual Download Page 118

 

 

Nuvo-7160GC/ Nuvo-7164GC Series 

118 

4.1.12  Boot Type (Legacy/ UEFI) 

The system supports both Legacy and Unified Extensible Firmware Interface (UEFI) boot 

modes. UEFI is a specification proposed by Intel to define a software interface between 

operating system and platform firmware. Most modern operating systems, such as Windows 

10 and Linux support both Legacy and UEFI boot modes. The Legacy boot mode uses MBR 

partition for disk and VBIOS for video initialization, the UEFI boot mode uses GPT partition 

which supports greater than 2TB partition size and GOP driver for faster video initialization. 

 

NOTE

 

If you choose Legacy mode, you will not be able to create disk partitions greater than 2TB or 

use TPM 2.0 function. 

To configure Boot Type: 

1. 

When system boots up, press F2 to enter BIOS setup utility. 

2. 

Go to 

[Boot]>[Boot Type]

, press Enter to bring up options, Dual Boot (UEFI), 

Legacy Boot Type, UEFI Boot Type. 

3. 

Highlight your selection and press Enter. 

4. 

Press F10 to “Exit Saving Changes”. 

Summary of Contents for Nuvo-7160GC Series
































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands