2. FIELD OF APPLICATION
The ROCK actuator is intended for use in the ventilation and air conditioning of rooms
through windows, sunscreen blades, louvre windows or jalousies. Th
obtained with 110/230V~ or low
gear motor controlled by a functional electronic device. The Syncro³ technology patented
by Nekos allows you to create synchronized systems of up to eight machines without any
control unit.
3. FORMULAS AND ADVICE FOR INSTALLATION
3.1.
Calculation of opening / closure force
Using the formulas on this page, approximate calculations can be made for the force
required to open or close the window considering all the factors that determine the
calculation.
The force required to move sunscreen blades, louvre windows or jalousies d
clutch system used on the fulcrums, the size of the blades and the wind pressure.
Therefore, the calculation should be made by the system manufacturer
specification data.
Symbols used for the calculation
F
(Kg) = Force for opening or closing
C
(cm) = Opening stroke (actuator stroke)
For horizontal light domes or skylights
F = 0,54 x P
(Eventual weight of snow or wind on the
cupola should be calculated separately)
3.2.
Maximum opening according to height of sash
The choice of actuator stroke depends on the window height and its use with sunscreen
blades or louvre windows. Check that the actuator does not touch the window profile during
its stroke, that no obstacles imped
window frame.
W
ARNING
. For safety, always check the application before fixing the actuator to the
window. If difficulties arise, consult the manufacturer to check the application.
5
FIELD OF APPLICATION
intended for use in the ventilation and air conditioning of rooms
through windows, sunscreen blades, louvre windows or jalousies. Th
230V~ or low-voltage (24V
SELV) electrical energy that powers a
functional electronic device. The Syncro³ technology patented
by Nekos allows you to create synchronized systems of up to eight machines without any
FORMULAS AND ADVICE FOR INSTALLATION
Calculation of opening / closure force
Using the formulas on this page, approximate calculations can be made for the force
required to open or close the window considering all the factors that determine the
The force required to move sunscreen blades, louvre windows or jalousies d
clutch system used on the fulcrums, the size of the blades and the wind pressure.
Therefore, the calculation should be made by the system manufacturer
Symbols used for the calculation
opening or closing
P
(Kg) = Weight of the window (mobile sash only)
Opening stroke (actuator stroke)
H
(cm) = Height of the mobile sash
For horizontal light domes or skylights
(Eventual weight of snow or wind on the
should be calculated separately)
.
For vertical windows
♦
TOP HUNG WINDOWS
,
OUTWARD OPENING
♦
BOTTOM HUNG WINDOWS
F = 0,54 x P x C : H
(Eventual load of favourable or unfavourable wind
on the sash should be calculated separately.)
Maximum opening according to height of sash
The choice of actuator stroke depends on the window height and its use with sunscreen
windows. Check that the actuator does not touch the window profile during
its stroke, that no obstacles impede opening and there is no forcing of
For safety, always check the application before fixing the actuator to the
window. If difficulties arise, consult the manufacturer to check the application.
intended for use in the ventilation and air conditioning of rooms
through windows, sunscreen blades, louvre windows or jalousies. The movement is
SELV) electrical energy that powers a
functional electronic device. The Syncro³ technology patented
by Nekos allows you to create synchronized systems of up to eight machines without any
Using the formulas on this page, approximate calculations can be made for the force
required to open or close the window considering all the factors that determine the
The force required to move sunscreen blades, louvre windows or jalousies depends on the
clutch system used on the fulcrums, the size of the blades and the wind pressure.
Therefore, the calculation should be made by the system manufacturer, who knows their
Weight of the window (mobile sash only)
Height of the mobile sash
For vertical windows
OUTWARD OPENING
(A)
BOTTOM HUNG WINDOWS
(B)
F = 0,54 x P x C : H
(Eventual load of favourable or unfavourable wind
on the sash should be calculated separately.)
The choice of actuator stroke depends on the window height and its use with sunscreen
windows. Check that the actuator does not touch the window profile during
ere is no forcing of the rod on the
For safety, always check the application before fixing the actuator to the
window. If difficulties arise, consult the manufacturer to check the application.
4. TECHNICAL OPERATING
ROCK
is fitted with control electronics. It is equipped with a stiff rod that moves the levers
of sunscreen blades or pushes the sash of a window or domed rooflight.
The stroke of the rod can be programmed along its entire
magnetic switch (magnet-holder screw)
The product is built in two versions, for a 110
low-voltage supply, with a maximum stroke of: 100 mm, 200 mm and 300 mm. It
factory with the rod completely closed and can therefore also be installed without
electricity, leaving the window closed after installation.
The return limit switch uses a
and therefore there are no adjustments to be made.
The gear motor unit structure is made from high
35%GF)
, with an IP66 protection rating, while the rod and reaction tube are made of
anodised aluminium alloy. The steel brackets, treat
the actuator and are fixed to the frame or window with screws.
ROCK 24V combined with the
and provides perfect window closure to ensure high thermal insulation values.
Window opening is easily programmed during installation by memorising the two
positions (
OPEN
and
CLOSED
).
ramp to place less stress on the structural parts and extend their life, and it is also a safety
device in accordance with standard EN 60335
5. MANUFACTURE AND REGULATORY FRAMEWORK
INTENDED USE.
The
ROCK
sunscreen blades, louvre
skylights; any other use is not recommended without prior approval from the manufacturer.
However, it should be noted that the installer of the entire system has sole responsibility
for the application, as well as for failure to comply with the instructions given in this
manual, as specified in the Machinery Directive.
The actuator is manufactured in accordance with the Directives and following
Regulations listed in the attached Declaration of Incorporation and Conformity
Electrical connections must conform to regulations in force for the des
electrical equipment.
The actuator is individually packaged in a cardboard box.
Each package contains:
1 Electric actuator complete with a 2 m power cable;
Actuator attachment hardware comprising: 2 brackets for attaching the actuator
M6x30 bolts and 2 self-locking M6 nuts.
Instruction manual.
6
TECHNICAL OPERATING INFORMATION
is fitted with control electronics. It is equipped with a stiff rod that moves the levers
of sunscreen blades or pushes the sash of a window or domed rooflight.
The stroke of the rod can be programmed along its entire stroke length
holder screw) (
see section 12
-
Programming the actuator
uilt in two versions, for a 110-230V~ 50/60Hz electrical supply or a 24V
voltage supply, with a maximum stroke of: 100 mm, 200 mm and 300 mm. It
factory with the rod completely closed and can therefore also be installed without
electricity, leaving the window closed after installation.
uses an electronic self-regulating process with power absorption
there are no adjustments to be made.
The gear motor unit structure is made from high-strength composite material
protection rating, while the rod and reaction tube are made of
alloy. The steel brackets, treated against corrosion, are supplied with
the actuator and are fixed to the frame or window with screws.
ROCK 24V combined with the
K-LOCK
product creates a burglar
and provides perfect window closure to ensure high thermal insulation values.
Window opening is easily programmed during installation by memorising the two
.
The actuator movement is equipped with a
ramp to place less stress on the structural parts and extend their life, and it is also a safety
device in accordance with standard EN 60335-2-103.
MANUFACTURE AND REGULATORY FRAMEWORK
ROCK
actuator is designed and built principally to open and close
louvre windows and jalousies, as well as domed rooflights or industrial
skylights; any other use is not recommended without prior approval from the manufacturer.
uld be noted that the installer of the entire system has sole responsibility
for the application, as well as for failure to comply with the instructions given in this
manual, as specified in the Machinery Directive.
The actuator is manufactured in accordance with the Directives and following
Regulations listed in the attached Declaration of Incorporation and Conformity
Electrical connections must conform to regulations in force for the des
The actuator is individually packaged in a cardboard box.
1 Electric actuator complete with a 2 m power cable;
Actuator attachment hardware comprising: 2 brackets for attaching the actuator
locking M6 nuts.
is fitted with control electronics. It is equipped with a stiff rod that moves the levers
of sunscreen blades or pushes the sash of a window or domed rooflight.
stroke length by means of a
Programming the actuator
).
230V~ 50/60Hz electrical supply or a 24V
voltage supply, with a maximum stroke of: 100 mm, 200 mm and 300 mm. It leaves the
factory with the rod completely closed and can therefore also be installed without
regulating process with power absorption
strength composite material
(Pa6 +
protection rating, while the rod and reaction tube are made of
ed against corrosion, are supplied with
product creates a burglar-proof window system
and provides perfect window closure to ensure high thermal insulation values.
Window opening is easily programmed during installation by memorising the two stoke-end
ovement is equipped with a start and stop
ramp to place less stress on the structural parts and extend their life, and it is also a safety
s designed and built principally to open and close
windows and jalousies, as well as domed rooflights or industrial
skylights; any other use is not recommended without prior approval from the manufacturer.
uld be noted that the installer of the entire system has sole responsibility
for the application, as well as for failure to comply with the instructions given in this
The actuator is manufactured in accordance with the Directives and following
Regulations listed in the attached Declaration of Incorporation and Conformity
Electrical connections must conform to regulations in force for the design and set up of
Actuator attachment hardware comprising: 2 brackets for attaching the actuator and rod, 2
