background image

9.1.12  STAY ALERT
Watch what you are doing. Use common sense. Do not operate compressor when you are tired. 
Compressor should never be used if you are under the influence of alcohol, drugs or medication
that makes you drowsy.
9.1.13 CHECK DAMAGED PARTS AND AIR LEAK
Before further use of the compressor, a guard or other part should be carefully checked to 
determine that it will operate properly and perform its intended function. Check for alignment 
of moving parts, binding of moving parts, breakage of parts, mounting, air leak, and any other 
conditions that may affect its operation. A guard or other part that is damaged should be properly
 repaired or replaced by an authorized service center unless otherwise indicated elsewhere in this
 Instruction Manual. Have defective pressure switches replaced by authorized service center. 
Do not use compressor if Switch dose not turn it on and off.
9.1.14  HANDLE COMPRESSOR CORRECTLY
Operate the compressor according to the instructions provided herein. Never allow the compressor
 to be operated by children, individuals unfamiliar with its operation or unauthorized personnel.
9.1.15 KEEP ALL SCREWS, BOLTS AND COVERS TIGHTLY IN PLACE
Keep all screws, bolts, and plates tightly mounted. Check their conditions periodically.
9.1.16  KEEP MOTOR AIR VENT CLEAN
The motor air vent must be kept clean so that air can freely flow at all times. Check for dust 
build-up frequently
9.1.17  NEVER USE A COMPRESSOR WHICH IS DEFECTIVE OR OPERATING ABNORMALLY
If the compressor appears to be operating unusually, making strange noises, or otherwise 
appears defective, stop using it immediately and arrange for repairs by an authorized service center.
9.1.18 DO NOT WIPE PLASTIC PARTS WITH SOLVENT
Solvents such as gasoline, thinner, benzene, carbon tetrachloride, and alcohol may damage and
 crack plastic parts. Do not wipe them with such solvents. Wipe plastic parts with a soft cloth lightly
 dampened with soapy water and dry thoroughly.
9.1.19 USE ONLY GENUINE REPLACEMENT PARTS
Replacement parts not original may void your warranty and lead to malfunction and resulting injuries. 
Genuine parts are available from your dealer.
9.1.20 DO NOT MODIFY THE COMPRESSOR
Do not modify the compressor.  Always contact the authorized service center and repairs. 
Unauthorized modification may not only impair the compressor performance, but also may
result in accident or injuries to repair personnel who do not have the required knowledge and 
technical expertise to perform the repair operations correctly.
9.1.21 TURN OFF THE PRESSURE SWITCH WHEN THE COMPRESSOR IS NOT USED
When the compressor is not used, turn the knob of the circuit breaker “OFF”, disconnect 
it from the power source and open the drain cock to discharge the compressed air from the air tank.
9.1.22 NEVER TOUCH HOT SURFACE
To reduce the risk of burns, do not touch tubes, heads, cylinder and motors.

Summary of Contents for CT4539









































Reviews: