background image

 

Fan Direction 
16. To change the direction of the fan from   

horizontal to vertical, loosen the Lock Ring   
and turn the Nozzle 90°.   

 
17. After the adjustment, tighten the Lock Ring   

by hand. 

 
 
 
 

Spraying Technique 

IMPORTANT: Proper spraying technique is ESSENTIAL to achieve good results. 
1. First, clean and prepare the Spray Gun according to the instructions under 

Before First Use on page 5 and Spray Gun Setup Adjustment on page 6. 

2. Keep the Spray Gun upright and at a right angle to the workpiece 

–   

See Figure M and Figure N. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 
3. Using two hands, one to steady the Cup and the other to operate the Spray Gun, 
aim Nozzle at the workpiece. 

CAUTION:

 

DO NOT STOP WHEN SPRAYING.

Spraying materials will start to set and dry 

 

as soon as they come in contact with the air. They will cause a permanent clog if not cleared 
immediately. If discontinuing spraying for more than half an hour, turn off the air supply, 
disconnect Cup from Gun Body and thoroughly rinse Cup and Gun Body with fresh, clean 
water. 
4. Pull Trigger slowly and move Spray Gun in parallel strokes to the workpiece. Keep the 

distance from the workpiece at about 6

” to 9” , depending on the flow adjustment and the 

paint. 

5. To avoid paint build up, start moving the Spray Gun before squeezing the Trigger. 

Summary of Contents for CT2308













Reviews: