NEC XN120 Vision Feature Manual Download Page 54 | Manualshive

Page: 54 / 222

NEC XN120 Vision Feature Manual Download Page 54

Features

Features Manual

52

Class of Service Options (Supplementary Service), Program 20-13

Default

Item
No.

Item

Input
Data

COS1 - 15

01

Long Conversation Alarm

Enables/disables the Warning Tone for Long Conversation (not for SLTs)

0- Off
1- On

1

02

Long Conversation Cutoff (Incoming)

Enables/disables an extension’s ability to use Long Conversation Cut-off for
incoming calls.

0- Off
1- On

0

03

Long Conversation Cutoff (Outgoing)

Enables/disables an extension’s ability to use Long Conversation Cut-off for
outgoing calls.

0- Off
1- On

0

04

Call Forwarding/DND Override

Enables/disables an extension’s ability to use Call Forwarding/DND Override.

0- Off
1- On

1

05

Automatic Off Hook Signaling (for KST)/Call Waiting (for SLT)

Allows a busy extension to manually (0) or automatically (1) receive off hook
signals.

0- Off
1- On

1

06

Automatic Off Hook Signaling

Allows a busy extension to manually (0) or automatically (1) receive off hook
signals.

0- Off
1- On

0

07

Message Waiting

Enables/disables an extension’s ability to leave Message Waiting.

0- Off
1- On

1

08

Conference

Enables/disables an extension’s ability to initiate a conference or Meet Me
Conference.

0- Off
1- On

1

09

Privacy Release

Enables/disables an extension’s ability to initiate a Voice Call Conference.

0- Off
1- On

1

10

Barge In Mode

Enables the extension’s Barge In to be speech mode (0) or Monitor mode (1).

0- Off
1- On

0

11

Room Monitor, Initiating Extension

Enable/disable an extension’s ability to initiate Room Monitor.

0- Off
1- On

0

12

Room Monitor, Extension Being Monitored

Enable/disable an extension’s ability to be monitored.

0- Off
1- On

0

13

Continued Dialling

Enable/disable an extension’s ability to use Continued Dialling which allows
DTMF signal sending while talking on extension.

0- Off
1- On

1

14

Department Calling

Enable/disable an extension’s ability to call a Department Group.

0- Off
1- On

1

15

Barge In, Initiate

Enables/disables Barge In at initiating extension.

0- Off
1- On

1

16

Barge In, Receive

Blocks/allows Barge In at the receiving extension.

0- Off
1- On

1

17

Barge In Tone/Display

Use this option to enable/disable the Barge In tone. If enabled, callers hear an
alert tone and their display indicates the Barge In when another extension
barges into their conversation. If disabled, there is no alert tone or display
indication.

0- Off
1- On

1

18

Programmable Function Key Programming (General Level)

Enables/disables an extension’s ability to program their General function keys
using Service Code 851 (by default). (Refer to Program 20-07-10 for Service
Code 852.)

0- Off
1- On

1

19

Selectable Display Messaging

Enables/disables an extension’s ability to use Selectable Display Messaging.

0- Off
1- On

1

«
...
52
53
54
55
56
...
»

Summary of Contents for XN120 Vision































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands