NEC XN120 Vision Feature Manual Download Page 53

Page: 53 / 222

Features

Features Manual

Class of Service Options (Answer Service), Program 20-11

Default

Item
No.

Item

Input
Data

COS1 - 15

Call Forward Immediately

Enables/disables an extension’s ability to use Immediate Call Forward

0- Off
1- On

Call Forward When Busy

Enables/disables an extension’s ability to use Call Forward When Busy.

0- Off
1- On

Call Forwarding When Unanswered

Enables/disables an extension’s ability to use Call Forward When
Unanswered.

0- Off
1- On

Call Forwarding (Both Ringing)

Enables/Disables an extension’s ability to activate Call Forwarding with Both
Ringing.

0- Off
1- On

Call Forwarding with Follow Me

Enables/disables an extension’s ability to initiate Call Forwarding with
Follow Me.

0- Off
1- On

Unscreened Transfer

Enables/disables an extension’s ability to use Unscreened Transfer.

0- Off
1- On

Transfer Without Holding

Enables/disables an extension’s ability to use Transfer Without Holding.

0- Off
1- On

Transfer Information Display

Enables/disables an extension’s incoming Transfer pre-answer display.

0- Off
1- On

Group Hold Initiate

Enables/disables an extension’s ability to initiate a Group Hold.

0- Off
1- On

Group Hold Answer

Enables/disables an extension’s ability to pick up a call on Group Hold

0- Off
1- On

Automatic On Hook Transfer

Enables/disables an extension’s ability to use Automatic On Hook Transfer.

0- Off
1- On

Call Forwarding Off-Premise

Enables/disables an extension’s ability to set up Call Forwarding Off-Premise
for their phone.

0- Off
1- On

Operator Transfer After Hold Callback

Enables/disables an extension’s ability to have a call which recalls from hold
transfer to the operator.

0- Off
1- On

Trunk to Trunk Transfer Restriction

0- Off
1- On

VRS Personal Greeting

Enables/disables extension’s ability to dial Service Code *47 to record, listen
to or erase the General Message.

0- Off
1- On

Call Redirect

Enable or disable a system phone user’s ability to transfer a call to a
pre-defined destination (such as an operator, voice mail, or another extension)
without answering the call.

0- Off
1- On

Call transfer setup for each telephone group

0- Off
1- On

No Recall

Allow (0) or prevent (1) answered Transferred calls from recalling the
originating extension.

0- Off
1- On

Normal/Extended Park

Determine if an extension’s Class of Service should allow either a normal or
extended Park.

0-Normal
1-Extende

Ring Inward recall disable

On-Hook Trunk to Trunk Transfer Restriction

Summary of Contents for XN120 Vision































































































































































































































Search results

Summary of Contents for XN120 Vision

Reviews:

Brands by name

Popular brands

NEC XN120 Vision, Feature Manual

Search results

Summary of Contents for XN120 Vision

Reviews:

Brands by name

Popular brands