NEC PD750004 User Manual Download Page 213

Page: 213 / 342

193

CHAPTER 6 INTERRUPT AND TEST FUNCTIONS

Figure 6-6. Format of Edge Detection Mode Registers

(a) INT0 edge detection mode register (IM0)

(b) INT1 edge detection mode register (IM1)

Caution Changing the edge detection mode register may set an interrupt request flag. So, disable

the interrupts before changing the edge detection mode register. Then clear the interrupt

request flag with a CLR1 instruction and enable the interrupts. When f

/64 is selected

as a sampling clock pulse in changing IM0, wait for 16 machine cycles after changing the

mode register and clear the interrupt request flag.

FB4H

Address

Specifies rising edge.

Specifies falling edge.

Detection edge specification

IM01

IM00

Specifies both rising and falling edges.

Ignored (No interrupt request flag is set.)

IM03

IM02

IM01

IM00

IM0

Symbol

Selects a noise eliminator.

Does not select a noise eliminator.

Noise eliminator selection bit

Enabled

Disabled

IM02

Sampling

Cannot be released

Can be released

Standby mode

(0.67 µs, 1.33 µs, 2.67 µs, and 10.7 µs at 6.00 MHz)

/64 (10.7 µs at 6.00 MHz)

Sampling clock

IM03

FB5H

Address

Specifies rising edge.

Specifies falling edge.

Detection edge specification

IM10

IM1

Symbol

Summary of Contents for PD750004























































































































































































































































































































































Search results

Summary of Contents for PD750004

Reviews:

NEC PD750004, User Manual, Page: 213 / 342

Search results

Summary of Contents for PD750004

Reviews: