background image

 

 

 

Adjusting the Projector

 

Plastic Cap Installation

 

Adjustment
Screw

M5 Allen
Wrench

Flat Tip
Screwdriver

Spindle

 

Step 1

.  Firmly grasp the projector in both hands, and slowly tilt 

 

either forward or backward, side-to-side to adjust and 

 level. 

Step 2. 

Tighten the M5 adjustment screws (located on each side 

 

of the spindle) using the M5 Allen wrench to keep the 

 

image aligned on the screen. 

 

 

Secure all mounting hardware before installing 
the plastic cap.

 

 

In the event that precision adjustments are needed, 
a flat tip screwdriver may be used to make small, 
even adjustments. In order to make these 
adjustments, completely tighten the M5 
adjustment screws at this time. Place the tip of the 
screwdriver between the projector plate and the lip 
of the spindle and adjust using the screwdriver. 
Once the adjustments have been made, re-tighten 
the adjustment screws on each side using the 
supplied M5 Allen wrench.

 

Step 1. 

Place a plastic cap over each leveling barrel and firmly 

 

push the plastic cap into place.

 

 

 

 

Installation Manual  

Page - 9 - 

Summary of Contents for NP30UCM













Reviews: