Appendix C Target ID Binding in Windows OS
You can bind the Bind the target Device's SCSI number and SCSI target num, by latter procedures.
The target Device’s SCSI number or SCSI target mum might swap after
reboot, if not binding Target ID.
Bind the target Device’s SCSI number and SCSI target num, if the system
corresponds to the following.
- Tape storage is connected via Fibre Channel switch.
- Multiple disk arrays (no drive letter) are connected via Fibre Channel
switch.
In Windows Server 2008(x86), this product doesn’t support Target ID
binding.
Process of Binding Target ID
㻌
1> Confirm the WWPN address of this product, tape storage and disk array which will be set binding.
Referring to the user’s guide of tape storage and disk array as appropriate.
2> Boot the system and log in it using the Administrator.
3> Open a Command Prompt and move to the OneCommand Manager (CLI) installed directory. The
default installation directory is \Emulex\Util\OCManager under “Program Files”.
㻌
㻹㼕㼏㼞㼛㼟㼛㼒㼠㻌 㼃㼕㼚㼐㼛㼣㼟㻌 㼇㼂㼑㼞㼟㼕㼛㼚㻌 㻢㻚㻝㻚㻣㻢㻜㻝㼉㻌
㻯㼛㼜㼥㼞㼕㼓㼔㼠㻌 㻔㼏㻕㻌 㻞㻜㻜㻥㻌 㻹㼕㼏㼞㼛㼟㼛㼒㼠㻌 㻯㼛㼞㼜㼛㼞㼍㼠㼕㼛㼚㻚㻌 㻌 㻭㼘㼘㻌 㼞㼕㼓㼔㼠㼟㻌 㼞㼑㼟㼑㼞㼢㼑㼐㻚㻌
㻌
㻯㻦㼈㼁㼟㼑㼞㼟㼈㻭㼐㼙㼕㼚㼕㼟㼠㼞㼍㼠㼛㼞㻪㼏㼐㻌 㻯㻦㼈㻼㼞㼛㼓㼞㼍㼙㻌 㻲㼕㼘㼑㼟㼈㻱㼙㼡㼘㼑㼤㼈㼁㼠㼕㼘㼈㻻㻯㻹㼍㼚㼍㼓㼑㼞㼈㻌
㻌
OneCommand Manager (CLI) and the driver of this product will be installed
at the same time. If OneCommand Manager (CLI) has not installed, apply
Starter Pack for the computer and the OS.
䣖䣫䣲䣵
䣖䣫䣲䣵
䣐䣱䣶䣫䣥䣧
Summary of Contents for N8190-159
