NEC N8120-011F Page 57 User Manual Download

Page: 57 / 166

About US40a 37

Advanced

If you move the cursor to [Advanced], then the Advanced menu appears.

The items which can be set on the Advanced menu screen and their functions are described below.

See the table below for the items.

Item

Parameter

Description

Legacy USB Support

[Enabled]
Disabled

Enables or disables support of USB ports.

Panel Type

[07]

Do not change this value.

Resume On RTC Alarm

Enabled
[Disabled]

Do not change this value.

Primary Battery Calibration

–

Allows you to calibrate the battery pack
installed in the standard battery bay.

Secondly Battery Calibration

–

Allows you to calibrate the battery pack
installed in the additional battery bay.

All Battery Calibration

–

Allows you to calibrate both the battery pack
installed in the standard battery bay and that in
additional battery bay concurrently.

Blue Tooth Device

Enabled
[Disabled]

Do not change the factory setting.

3G Device

Enabled
[Disabled]

Do not change factory setting.

Wireless LAN Device

[Enabled]
Disabled

Enables or disables support of wireless LAN
device.

[ ]: Factory-set value

Summary of Contents for N8120-011F







































































































































































Search results

Summary of Contents for N8120-011F

Reviews:

Related manuals for N8120-011F

Brands by name

Popular brands

NEC N8120-011F, User Manual

Search results

Summary of Contents for N8120-011F

Reviews:

Related manuals for N8120-011F

Brands by name

Popular brands