background image

English-2

Registration Information

Cable information

 CAUTION:

   Use the provided specified cables with this monitor so as not to interfere with radio and television reception.

For HDMI, DisplayPort, USB and USB-C, please use a shielded signal cable. Use of other cables and adapters 
may cause interference with radio and television reception.

FCC Information

 WARNING:

  The Federal Communications Commission does not allow any modifications or changes to the unit EXCEPT 

those specified by NEC Display Solutions of America, Inc. in this manual. Failure to comply with this government 
regulation could void your right to operate this equipment.

1.  

The power supply cord you use must have been approved by and comply with the safety standards of U.S.A., and meet 
the following condition.

Power supply cord
Plug shape

Non shield type, 3-conductor

U.S.A

2.  

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of 

the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential 
installation. This equipment generates, uses and can radiate radio frequency energy, and, if not installed and used 
in accordance with the instructions, may cause harmful interference to radio communications. However, there is no 
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to 
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try 
to correct the interference by one or more of the following measures:

 

• 

Reorient or relocate the receiving antenna.

 

• 

Increase the separation between the equipment and receiver.

 

• 

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

 

 

• 

Consult the dealer or an experienced radio/TV technician for help.

 

 
If necessary, the user should contact the dealer or an experienced radio/television technician for additional suggestions. 
The user may find the following booklet, prepared by the Federal Communications Commission, helpful: “How to Identify 
and Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. Government Printing Office, 
Washington, D.C., 20402, Stock No. 004-000-00345-4.

Declaration of Conformity

This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may not 
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause 
undesired operation.

U.S. Responsible Party:  NEC Display Solutions of America, Inc. 
Address: 

 

3250 Lacey Rd, Ste 500 

 

   

 

Downers Grove, IL 60515 

Tel. No.:  

 

630-467-3000

Type of Product: 

Display Monitor

Equipment Classification:  Class B Peripheral

Model: 

MultiSync EA271U (EA271U, EA271U-BK)

We hereby declare that the equipment specified above conforms 

to the technical standards as specified in the FCC Rules.

To see a list of our TCO certified monitors and their TCO Certification (in English only), visit our website at

https://www.nec-display.com/global/about/legal_regulation/TCO_mn/index.html

 CAUTION:

  Please confirm the distribution system in building installation shall provide the circuit breaker rated 120/240V, 

20A (maximum).

Summary of Contents for MultiSync EA271U-BK






































Reviews: