background image

CHAPTER  2   PART  NAMES

User’s Manual  U16290EJ1V0UM

17

2.2   Initial Switch and Jumper Settings

The initial switch and jumper settings of the IE-789835-NS-EM1 are shown in Table 2-1.

For the setting of JP2, refer to 

3.4 Clock Settings

.

For the settings of SW1 to SW6, refer to 

3.6 LCD Emulation

.

Table 2-1.  Initial Switch and Jumper Settings

JP2

Initial setting

2 and 3 shorted

SW1

SW2

SW3

SW4

SW5

SW6

Initial setting

OFF

ICE side

ICE side

ICE side

ICE side

ICE side

2.3   Check Point Block

The through holes of the check point block (refer to 

Figure 2-1 IE-789835-NS-EM1 Part Names

) are provided at

intervals of 2.54 mm (1 inch) both vertically and horizontally, allowing confirmation of the signal of each port pin

inside the IE-789835-NS-EM1.

Figure 2-2.  Check Point Block

Signals inside IE system

P00, P01, P02, P03, P04, P05, P06, P07

P10, P11, P60, P61, P62, N.C, N.C, N.C

P20, P21, P22, P23, P24, P25, P26, P27

Signals inside IE system

Signals inside IE system

Signals inside IE system

P80, P81, P82, P83, P84, P85, P86, P87

P30, P31, P32, P33, P34, P35, P36, P37

Caution

Do not connect or capture the signal inside the IE system, or the IE system may be damaged.

Remark

The through holes indicated by 

 

 (N.C.) are not connected to any signal.

Summary of Contents for IE-789835-NS-EM1
















































Reviews: