NEC Express5800/R320c-E4 N8800-173F Installation Manual Download Page 16

Page: 16 / 267

1. Before Starting Setup

Express5800/R320c-E4, R320c-M4, R320d-E4, R320d-M4 Installation Guide (Windows)

Chapter 1 Installing Operating System

1.2

Supported Windows OS

EXPRESSBUILDER supports the following editions of Windows operating systems:

See the next section (

1.3 Service Pack Support

) for Service Pack.

Name of Windows OS

Supported

Windows Server 2012

Windows Server 2012 Standard



Windows Server 2012 Datacenter



Windows Server 2008 R2

Windows Server 2008 R2 Standard

−

Windows Server 2008 R2 Enterprise



: Supported

−

: Not Supported

* : Supported on server with GUI or full installation only.

1.3

Service Pack Support

The following combination of operating system installation media and Service Packs are supported by
EXPRESSBUILDER.

Service Pack

Windows Server 2012

Windows Server 2008 R2

Service Pack 1 Included

–



NO Service Pack + Service Pack 1

–



NO Service Pack



−



: Supported

−

: Not Supported

1.4

Mass Storage Controllers Supported by EXPRESSBUILDER

The table below lists the mass storage controllers supported by the supplied EXPRESSBUILDER.

Windows Server 2012

Windows Server 2008 R2

Other options

N8803-038 Fibre Channel board kit
(8Gbps x 1ch)



: Supported by EXPRESSBUILDER

Summary of Contents for Express5800/R320c-E4 N8800-173F












































































































































































































































































Search results

Summary of Contents for Express5800/R320c-E4 N8800-173F

Reviews:

Brands by name

Popular brands

NEC Express5800/R320c-E4 N8800-173F, Installation Manual

Search results

Summary of Contents for Express5800/R320c-E4 N8800-173F

Reviews:

Brands by name

Popular brands